summaryrefslogtreecommitdiff
AgeCommit message (Collapse)AuthorFilesLines
2014-10-15r8169: add ethtool eeprom change/dump featurertl-eeprom-3.17Peter Wu2-3/+156
This adds the ability to read and change EEPROM for 93C46/93C56 serial EEPROM. Two-Wire serial interface and SPI are not supported. (Do not even try this for SPI or other chips, it may break your hardware.) Works with RTL8169SCL (driver detects RTL8169sb), with some quirks. Not sure if it is a hardware bug, but to be able to read EEPROM, one has to write something, e.g.: printf '\0\0' | ethtool -E eth0 magic 0x8169 offset 0x40 length 2 Otherwise, only zeroes are read. Another note for this NIC, one has to "enable" the eeprom by writing to it (as shown above) and then make the NIC to reload the contents from firmware such that the PCI ID gets detected correctly (10ec:8169 instead of 10ec:8129). Reload by writing 0x40 (Auto-load) to register 0x50 (9346CR): printf '\x40' | dd seek=80 bs=1 \ of=/sys/bus/pci/devices/0000:03:00.0/resource0 Then detach and rescan the PCI device (use `lspci -tv` to find parent): echo 1 > /sys/bus/pci/devices/0000\:03\:00.0/remove echo 1 > /sys/bus/pci/devices/0000\:02\:00.0/rescan After this, this RTL8169sb PCI GbE NIC appears to work. On a second RTL8188E onboard GbE chip, EEPROM cannot be dumped, writing also does nothing. Here, reads all return FFs. Signed-off-by: Peter Wu <lekensteyn@gmail.com>
2014-10-15Linux 3.17.1Greg Kroah-Hartman1-1/+1
2014-10-15arm64: Tell irq work about self IPI supportFrederic Weisbecker4-2/+14
commit 3631073659d0aafeaa52227bb61a100efaf901dc upstream. ARM64 irq work self-IPI support depends on __smp_cross_call to point to some relevant IRQ controller operations. This information should be available after the call to init_IRQ(). Lets implement arch_irq_work_has_interrupt() accordingly. Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Acked-by: Catalin Marinas <catalin.marinas@arm.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Will Deacon <will.deacon@arm.com> Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-10-15libata: Un-break ATA blacklistGeorge Spelvin1-2/+2
commit 1c40279960bcd7d52dbdf1d466b20d24b99176c8 upstream. lib/glob.c provides a new glob_match() function, with arguments in (pattern, string) order. It replaced a private function with arguments in (string, pattern) order, but I didn't swap the call site... The result was the entire ATA blacklist was effectively disabled. The lesson for today is "I f***ed up *how* badly *how* many months ago?", er, I mean "Nobody Tests RC Kernels On Legacy Hardware". This was not a subtle break, but it made it through an entire RC cycle unreported, presumably because all the people doing testing have full-featured hardware. (FWIW, the reason for the argument swap was because fnmatch() does it that way, and for a while implementing a full fnmatch() was being considered.) Fixes: 428ac5fc056e0 (libata: Use glob_match from lib/glob.c) Reported-by: Steven Honeyman <stevenhoneyman@gmail.com> Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=71371#c21 Signed-off-by: George Spelvin <linux@horizon.com> Tested-by: Steven Honeyman <stevenhoneyman@gmail.com> Signed-off-by: Tejun Heo <tj@kernel.org> Cc: Henrique de Moraes Holschuh <hmh@hmh.eng.br> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-10-15serial: 8250: Add Quark X1000 to 8250_pci.cBryan O'Donoghue1-0/+21
commit 1ede7dcca3c4fa15a518ab0473126f9c3e621e4c upstream. Quark X1000 contains two designware derived 8250 serial ports. Each port has a unique PCI configuration space consisting of BAR0:UART BAR1:DMA respectively. Unlike the standard 8250 the register width is 32 bits for RHR,IER etc The Quark UART has a fundamental clock @ 44.2368 MHz allowing for a bitrate of up to about 2.76 megabits per second. This patch enables standard 8250 mode Signed-off-by: Bryan O'Donoghue <pure.logic@nexus-software.ie> Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-10-15driver/base/node: remove unnecessary kfree of node struct from ↵Yasuaki Ishimatsu1-1/+0
unregister_one_node commit 33ead538f642a33b1d658782a5d14a40b5014d1f upstream. Commit 92d585ef067d ("numa: fix NULL pointer access and memory leak in unregister_one_node()") added kfree() of node struct in unregister_one_node(). But node struct is freed by node_device_release() which is called in unregister_node(). So by adding the kfree(), node struct is freed two times. While hot removing memory, the commit leads the following BUG_ON(): kernel BUG at mm/slub.c:3346! invalid opcode: 0000 [#1] SMP [...] Call Trace: [...] unregister_one_node [...] try_offline_node [...] remove_memory [...] acpi_memory_device_remove [...] acpi_bus_trim [...] acpi_bus_trim [...] acpi_device_hotplug [...] acpi_hotplug_work_fn [...] process_one_work [...] worker_thread [...] ? rescuer_thread [...] kthread [...] ? kthread_create_on_node [...] ret_from_fork [...] ? kthread_create_on_node This patch removes unnecessary kfree() from unregister_one_node(). Signed-off-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com> Cc: Xishi Qiu <qiuxishi@huawei.com> Fixes: 92d585ef067d "numa: fix NULL pointer access and memory leak in unregister_one_node()" Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-10-15crypto: caam - fix addressing of struct memberCristian Stoica1-3/+3
commit 4451d494b1910bf7b7f8381a637d0fe6d2142467 upstream. buf_0 and buf_1 in caam_hash_state are not next to each other. Accessing buf_1 is incorrect from &buf_0 with an offset of only size_of(buf_0). The same issue is also with buflen_0 and buflen_1 Signed-off-by: Cristian Stoica <cristian.stoica@freescale.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-10-15USB: Add device quirk for ASUS T100 Base Station keyboardLu Baolu3-2/+11
commit ddbe1fca0bcb87ca8c199ea873a456ca8a948567 upstream. This full-speed USB device generates spurious remote wakeup event as soon as USB_DEVICE_REMOTE_WAKEUP feature is set. As the result, Linux can't enter system suspend and S0ix power saving modes once this keyboard is used. This patch tries to introduce USB_QUIRK_IGNORE_REMOTE_WAKEUP quirk. With this quirk set, wakeup capability will be ignored during device configure. This patch could be back-ported to kernels as old as 2.6.39. Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-10-15usb: musb: dsps: kill OTG timer on suspendFelipe Balbi1-0/+2
commit 468bcc2a2ca071f652009d2d20d97f2437630cae upstream. if we don't make sure to kill the timer, it could expire after we have already gated our clocks. That will trigger a Data Abort exception because we would try to access register while clock is gated. Fix that bug. Fixes 869c597 (usb: musb: dsps: add support for suspend and resume) Tested-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-10-15USB: cp210x: add support for Seluxit USB dongleAndreas Bomholtz1-0/+1
commit dee80ad12d2b1b304286a707fde7ab05d1fc7bab upstream. Added the Seluxit ApS USB Serial Dongle to cp210x driver. Signed-off-by: Andreas Bomholtz <andreas@seluxit.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-10-15USB: serial: cp210x: added Ketra N1 wireless interface supportJoe Savage1-0/+1
commit bfc2d7dfdd761ae3beccdb26abebe03cef042f46 upstream. Added support for Ketra N1 wireless interface, which uses the Silicon Labs' CP2104 USB to UART bridge with customized PID 8946. Signed-off-by: Joe Savage <joe.savage@goketra.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-10-15Revert "usb: gadget: composite: dequeue cdev->req before free it in ↵Felipe Balbi1-1/+0
composite_dev_cleanup" commit bf17eba7ae1e813b0ad67cb1078dcbd7083b906e upstream. This reverts commit f2267089ea17fa97b796b1b4247e3f8957655df3. That commit causes more problem than fixes. Firstly, kfree() should be called after usb_ep_dequeue() and secondly, the way things are, we will try to dequeue a request that has already completed much more frequently than one which is pending. Cc: Li Jun <b47624@freescale.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-10-15usb: gadget: f_fs: signedness bug in __ffs_func_bind_do_descs()Dan Carpenter1-1/+2
commit 85b06f5e53d17c15844ef3cd45d0c7107f0ae45c upstream. We need "idx" to be signed for the error handling to work. Fixes: 6d5c1c77bbf9 ('usb: gadget: f_fs: fix the redundant ep files problem') Acked-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-10-15uas: Add another ASM1051 usb-id to the uas blacklistHans de Goede1-0/+8
commit 710f1bf16ab1b1558f099b62c5011c4cbba6a7bb upstream. As most ASM1051 based devices, this one has unfixable issues with uas too. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-10-15uas: Add US_FL_NO_ATA_1X quirk for Seagate (0bc2:ab20) drivesHans de Goede1-0/+7
commit f9554a6b199360c2f888173fd600e1eb7ff165ef upstream. https://bbs.archlinux.org/viewtopic.php?pid=1457492 Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-10-15uas: Add no-report-opcodes quirkHans de Goede5-1/+19
commit 734016b00b50a3c6a0e1fc1b7b217e783f5123a1 upstream. Besides the ASM1051 (*) needing sdev->no_report_opcodes = 1, it turns out that the JMicron JMS567 also needs it to work properly with uas (usb-storage always sets it). Since some of the scsi devs were not to keen on the idea to outrightly set sdev->no_report_opcodes = 1 for all uas devices, so add a quirk for this, and set it for the JMS567. *) Which has become a non-issue since we've completely blacklisted uas on the ASM1051 for other reasons Reported-and-tested-by: Claudio Bizzarri <claudio.bizzarri@gmail.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-10-15uas: Add a quirk for rejecting ATA_12 and ATA_16 commandsHans de Goede5-11/+35
commit 593078525c8b234a35a36ff551b8716464e86481 upstream. And set this quirk for the Seagate Expansion Desk (0bc2:2312), as that one seems to hang upon receiving an ATA_12 or ATA_16 command. https://bugzilla.kernel.org/show_bug.cgi?id=79511 https://bbs.archlinux.org/viewtopic.php?id=183190 While at it also add missing documentation for the u value for usb-storage quirks. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-10-15PCI: pciehp: Fix wait time in timeout messageYinghai Lu1-1/+1
commit d433889cd5a0933fbd90f1e65bff5a8d7963cc52 upstream. When we warned about a timeout on a hotplug command, we previously printed the time between calls to pcie_write_cmd(), without accounting for any time spent actually waiting. Consider this sequence: pcie_write_cmd write SLTCTL cmd_started = jiffies # T1 pcie_write_cmd pcie_wait_cmd now = jiffies # T2 wait_event_timeout # we may wait here if (timeout) ctrl_info("Timeout on command issued %u msec ago", jiffies_to_msecs(now - cmd_started)) We previously printed (T2 - T1), but that doesn't include the time spent in wait_event_timeout(). Fix this by using the current jiffies value, not the one cached before calling wait_event_timeout(). [bhelgaas: changelog, use current jiffies instead of adding timeout] Fixes: 40b960831cfa ("PCI: pciehp: Compute timeout from hotplug command start time") Signed-off-by: Yinghai Lu <yinghai@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-10-15arm: Tell irq work about self IPI supportFrederic Weisbecker3-2/+12
commit 09f6edd424218eb69078551b2ecfada1f2d098eb upstream. ARM irq work IPI support depends on SMP support. That information is partly known at early boottime. Lets implement arch_irq_work_has_interrupt() accordingly. Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Ingo Molnar <mingo@kernel.org> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Russell King <linux@arm.linux.org.uk> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-10-15x86: Tell irq work about self IPI supportFrederic Weisbecker3-2/+12
commit 3010279f0fc36f0388872203e63ca49912f648fd upstream. x86 supports irq work self-IPIs when local apic is available. This is partly known on runtime so lets implement arch_irq_work_has_interrupt() accordingly. This should be safely called after setup_arch(). Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Ingo Molnar <mingo@kernel.org> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-10-15irq_work: Force raised irq work to run on irq work interruptFrederic Weisbecker3-3/+15
commit 76a33061b9323b7fdb220ae5fa116c10833ec22e upstream. The nohz full kick, which restarts the tick when any resource depend on it, can't be executed anywhere given the operation it does on timers. If it is called from the scheduler or timers code, chances are that we run into a deadlock. This is why we run the nohz full kick from an irq work. That way we make sure that the kick runs on a virgin context. However if that's the case when irq work runs in its own dedicated self-ipi, things are different for the big bunch of archs that don't support the self triggered way. In order to support them, irq works are also handled by the timer interrupt as fallback. Now when irq works run on the timer interrupt, the context isn't blank. More precisely, they can run in the context of the hrtimer that runs the tick. But the nohz kick cancels and restarts this hrtimer and cancelling an hrtimer from itself isn't allowed. This is why we run in an endless loop: Kernel panic - not syncing: Watchdog detected hard LOCKUP on cpu 2 CPU: 2 PID: 7538 Comm: kworker/u8:8 Not tainted 3.16.0+ #34 Workqueue: btrfs-endio-write normal_work_helper [btrfs] ffff880244c06c88 000000001b486fe1 ffff880244c06bf0 ffffffff8a7f1e37 ffffffff8ac52a18 ffff880244c06c78 ffffffff8a7ef928 0000000000000010 ffff880244c06c88 ffff880244c06c20 000000001b486fe1 0000000000000000 Call Trace: <NMI[<ffffffff8a7f1e37>] dump_stack+0x4e/0x7a [<ffffffff8a7ef928>] panic+0xd4/0x207 [<ffffffff8a1450e8>] watchdog_overflow_callback+0x118/0x120 [<ffffffff8a186b0e>] __perf_event_overflow+0xae/0x350 [<ffffffff8a184f80>] ? perf_event_task_disable+0xa0/0xa0 [<ffffffff8a01a4cf>] ? x86_perf_event_set_period+0xbf/0x150 [<ffffffff8a187934>] perf_event_overflow+0x14/0x20 [<ffffffff8a020386>] intel_pmu_handle_irq+0x206/0x410 [<ffffffff8a01937b>] perf_event_nmi_handler+0x2b/0x50 [<ffffffff8a007b72>] nmi_handle+0xd2/0x390 [<ffffffff8a007aa5>] ? nmi_handle+0x5/0x390 [<ffffffff8a0cb7f8>] ? match_held_lock+0x8/0x1b0 [<ffffffff8a008062>] default_do_nmi+0x72/0x1c0 [<ffffffff8a008268>] do_nmi+0xb8/0x100 [<ffffffff8a7ff66a>] end_repeat_nmi+0x1e/0x2e [<ffffffff8a0cb7f8>] ? match_held_lock+0x8/0x1b0 [<ffffffff8a0cb7f8>] ? match_held_lock+0x8/0x1b0 [<ffffffff8a0cb7f8>] ? match_held_lock+0x8/0x1b0 <<EOE><IRQ[<ffffffff8a0ccd2f>] lock_acquired+0xaf/0x450 [<ffffffff8a0f74c5>] ? lock_hrtimer_base.isra.20+0x25/0x50 [<ffffffff8a7fc678>] _raw_spin_lock_irqsave+0x78/0x90 [<ffffffff8a0f74c5>] ? lock_hrtimer_base.isra.20+0x25/0x50 [<ffffffff8a0f74c5>] lock_hrtimer_base.isra.20+0x25/0x50 [<ffffffff8a0f7723>] hrtimer_try_to_cancel+0x33/0x1e0 [<ffffffff8a0f78ea>] hrtimer_cancel+0x1a/0x30 [<ffffffff8a109237>] tick_nohz_restart+0x17/0x90 [<ffffffff8a10a213>] __tick_nohz_full_check+0xc3/0x100 [<ffffffff8a10a25e>] nohz_full_kick_work_func+0xe/0x10 [<ffffffff8a17c884>] irq_work_run_list+0x44/0x70 [<ffffffff8a17c8da>] irq_work_run+0x2a/0x50 [<ffffffff8a0f700b>] update_process_times+0x5b/0x70 [<ffffffff8a109005>] tick_sched_handle.isra.21+0x25/0x60 [<ffffffff8a109b81>] tick_sched_timer+0x41/0x60 [<ffffffff8a0f7aa2>] __run_hrtimer+0x72/0x470 [<ffffffff8a109b40>] ? tick_sched_do_timer+0xb0/0xb0 [<ffffffff8a0f8707>] hrtimer_interrupt+0x117/0x270 [<ffffffff8a034357>] local_apic_timer_interrupt+0x37/0x60 [<ffffffff8a80010f>] smp_apic_timer_interrupt+0x3f/0x50 [<ffffffff8a7fe52f>] apic_timer_interrupt+0x6f/0x80 To fix this we force non-lazy irq works to run on irq work self-IPIs when available. That ability of the arch to trigger irq work self IPIs is available with arch_irq_work_has_interrupt(). Reported-by: Catalin Iacob <iacobcatalin@gmail.com> Reported-by: Dave Jones <davej@redhat.com> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Ingo Molnar <mingo@kernel.org> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-10-15irq_work: Introduce arch_irq_work_has_interrupt()Peter Zijlstra31-1/+42
commit c5c38ef3d70377dc504a6a3f611a3ec814bc757b upstream. The nohz full code needs irq work to trigger its own interrupt so that the subsystem can work even when the tick is stopped. Lets introduce arch_irq_work_has_interrupt() that archs can override to tell about their support for this ability. Signed-off-by: Peter Zijlstra <peterz@infradead.org> Cc: Ingo Molnar <mingo@kernel.org> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-10-15net_sched: copy exts->type in tcf_exts_change()WANG Cong1-0/+1
[ Upstream commit 5301e3e117d88ef0967ce278912e54757f1a31a2 ] We need to copy exts->type when committing the change, otherwise it would be always 0. This is a quick fix for -net and -stable, for net-next tcf_exts will be removed. Fixes: commit 33be627159913b094bb578e83 ("net_sched: act: use standard struct list_head") Reported-by: Jamal Hadi Salim <jhs@mojatatu.com> Cc: Jamal Hadi Salim <jhs@mojatatu.com> Cc: John Fastabend <john.fastabend@gmail.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-10-153c59x: fix bad split of cpu_to_le32(pci_map_single())Sylvain \\\"ythier\\\" Hitier1-1/+1
[ Upstream commit 88b09a6d958af6c458acf055ee2eb5bc9564efda ] In commit 6f2b6a3005b2c34c39f207a87667564f64f2f91a, # 3c59x: Add dma error checking and recovery the intent is to split out the mapping from the byte-swapping in order to insert a dma_mapping_error() check. Kinda this semantic patch: // See http://coccinelle.lip6.fr/ // // Beware, grouik-and-dirty! @@ expression DEV, X, Y, Z; @@ - cpu_to_le32(pci_map_single(DEV, X, Y, Z)) + dma_addr_t addr = pci_map_single(DEV, X, Y, Z); + if (dma_mapping_error(&DEV->dev, addr)) + /* snip */; + cpu_to_le32(addr) However, the #else part (of the #if DO_ZEROCOPY test) is changed this way: - cpu_to_le32(pci_map_single(DEV, X, Y, Z)) + dma_addr_t addr = cpu_to_le32(pci_map_single(DEV, X, Y, Z)); // ^^^^^^^^^^^ // That mismatches the 3 other changes! + if (dma_mapping_error(&DEV->dev, addr)) + /* snip */; + cpu_to_le32(addr) Let's remove the leftover cpu_to_le32() for coherency. v2: Better changelog. v3: Add Acked-by Fixes: 6f2b6a3005b2c34c39f207a87667564f64f2f91a # 3c59x: Add dma error checking and recovery Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: Sylvain "ythier" Hitier <sylvain.hitier@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-10-15sctp: handle association restarts when the socket is closed.Vlad Yasevich2-4/+17
[ Upstream commit bdf6fa52f01b941d4a80372d56de465bdbbd1d23 ] Currently association restarts do not take into consideration the state of the socket. When a restart happens, the current assocation simply transitions into established state. This creates a condition where a remote system, through a the restart procedure, may create a local association that is no way reachable by user. The conditions to trigger this are as follows: 1) Remote does not acknoledge some data causing data to remain outstanding. 2) Local application calls close() on the socket. Since data is still outstanding, the association is placed in SHUTDOWN_PENDING state. However, the socket is closed. 3) The remote tries to create a new association, triggering a restart on the local system. The association moves from SHUTDOWN_PENDING to ESTABLISHED. At this point, it is no longer reachable by any socket on the local system. This patch addresses the above situation by moving the newly ESTABLISHED association into SHUTDOWN-SENT state and bundling a SHUTDOWN after the COOKIE-ACK chunk. This way, the restarted associate immidiately enters the shutdown procedure and forces the termination of the unreachable association. Reported-by: David Laight <David.Laight@aculab.com> Signed-off-by: Vlad Yasevich <vyasevich@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-10-15hyperv: Fix a bug in netvsc_send()KY Srinivasan1-7/+8
[ Upstream commit 3a67c9ccad926a168d8b7891537a452018368a5b ] After the packet is successfully sent, we should not touch the packet as it may have been freed. This patch is based on the work done by Long Li <longli@microsoft.com>. David, please queue this up for stable. Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Reported-by: Sitsofe Wheeler <sitsofe@yahoo.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-10-15team: avoid race condition in scheduling delayed workJoe Lawrence1-2/+2
[ Upstream commit 47549650abd13d873fd2e5fc218db19e21031074 ] When team_notify_peers and team_mcast_rejoin are called, they both reset their respective .count_pending atomic variable. Then when the actual worker function is executed, the variable is atomically decremented. This pattern introduces a potential race condition where the .count_pending rolls over and the worker function keeps rescheduling until .count_pending decrements to zero again: THREAD 1 THREAD 2 ======== ======== team_notify_peers(teamX) atomic_set count_pending = 1 schedule_delayed_work team_notify_peers(teamX) atomic_set count_pending = 1 team_notify_peers_work atomic_dec_and_test count_pending = 0 (return) schedule_delayed_work team_notify_peers_work atomic_dec_and_test count_pending = -1 schedule_delayed_work (repeat until count_pending = 0) Instead of assigning a new value to .count_pending, use atomic_add to tack-on the additional desired worker function invocations. Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com> Acked-by: Jiri Pirko <jiri@resnulli.us> Fixes: fc423ff00df3a19554414ee ("team: add peer notification") Fixes: 492b200efdd20b8fcfdac87 ("team: add support for sending multicast rejoins") Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-10-15net: systemport: fix bcm_sysport_insert_tsb()Florian Fainelli1-6/+7
[ Upstream commit e87474a6e697857df21cff0707a2472abceca8b3 ] Similar to commit bc23333ba11fb7f959b7e87e121122f5a0fbbca8 ("net: bcmgenet: fix bcmgenet_put_tx_csum()"), we need to return the skb pointer in case we had to reallocate the SKB headroom. Fixes: 80105befdb4b8 ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-10-15ip6_gre: fix flowi6_proto value in xmit pathNicolas Dichtel1-2/+2
[ Upstream commit 3be07244b7337760a3269d56b2f4a63e72218648 ] In xmit path, we build a flowi6 which will be used for the output route lookup. We are sending a GRE packet, neither IPv4 nor IPv6 encapsulated packet, thus the protocol should be IPPROTO_GRE. Fixes: c12b395a4664 ("gre: Support GRE over IPv6") Reported-by: Matthieu Ternisien d'Ouville <matthieu.tdo@6wind.com> Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-10-05Linux 3.17Linus Torvalds1-1/+1
2014-10-05Merge tag 'scsi-fixes' of ↵Linus Torvalds4-7/+62
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi Pull SCSI fixes from James Bottomley: "This is a set of two small fixes, both to code which went in during the merge window: cxgb4i has a scheduling in atomic bug in its new ipv6 code and uas fails to work properly with the new scsi-mq code" * tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: [SCSI] uas: disable use of blk-mq I/O path [SCSI] cxgb4i: avoid holding mutex in interrupt context
2014-10-04Merge tag 'tiny/kconfig-for-3.17' of ↵Linus Torvalds1-0/+3
https://git.kernel.org/pub/scm/linux/kernel/git/josh/linux Pull kconfig fixes for tiny setups from Josh Triplett: "Two Kconfig bugfixes for 3.17 related to tinification. These fixes make the Kconfig "General Setup" menu much more usable" * tag 'tiny/kconfig-for-3.17' of https://git.kernel.org/pub/scm/linux/kernel/git/josh/linux: init/Kconfig: Fix HAVE_FUTEX_CMPXCHG to not break up the EXPERT menu init/Kconfig: Hide printk log config if CONFIG_PRINTK=n
2014-10-03init/Kconfig: Fix HAVE_FUTEX_CMPXCHG to not break up the EXPERT menuJosh Triplett1-0/+1
commit 03b8c7b623c80af264c4c8d6111e5c6289933666 ("futex: Allow architectures to skip futex_atomic_cmpxchg_inatomic() test") added the HAVE_FUTEX_CMPXCHG symbol right below FUTEX. This placed it right in the middle of the options for the EXPERT menu. However, HAVE_FUTEX_CMPXCHG does not depend on EXPERT or FUTEX, so Kconfig stops placing items in the EXPERT menu, and displays the remaining several EXPERT items (starting with EPOLL) directly in the General Setup menu. Since both users of HAVE_FUTEX_CMPXCHG only select it "if FUTEX", make HAVE_FUTEX_CMPXCHG itself depend on FUTEX. With this change, the subsequent items display as part of the EXPERT menu again; the EMBEDDED menu now appears as the next top-level item in the General Setup menu, which makes General Setup much shorter and more usable. Signed-off-by: Josh Triplett <josh@joshtriplett.org> Acked-by: Randy Dunlap <rdunlap@infradead.org> Cc: stable <stable@vger.kernel.org>
2014-10-03init/Kconfig: Hide printk log config if CONFIG_PRINTK=nJosh Triplett1-0/+2
The buffers sized by CONFIG_LOG_BUF_SHIFT and CONFIG_LOG_CPU_MAX_BUF_SHIFT do not exist if CONFIG_PRINTK=n, so don't ask about their size at all. Signed-off-by: Josh Triplett <josh@joshtriplett.org> Acked-by: Randy Dunlap <rdunlap@infradead.org> Cc: stable <stable@vger.kernel.org>
2014-10-03Merge branch 'i2c/for-current' of ↵Linus Torvalds2-5/+9
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux Pull i2c fixes from Wolfram Sang: "Two i2c driver bugfixes" * 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: i2c: qup: Fix order of runtime pm initialization i2c: rk3x: fix 0 length write transfers
2014-10-03Merge tag 'trace-fixes-v3.17-rc7' of ↵Linus Torvalds1-1/+1
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace Pull trace ring buffer iterator fix from Steven Rostedt: "While testing some new changes for 3.18, I kept hitting a bug every so often in the ring buffer. At first I thought it had to do with some of the changes I was working on, but then testing something else I realized that the bug was in 3.17 itself. I ran several bisects as the bug was not very reproducible, and finally came up with the commit that I could reproduce easily within a few minutes, and without the change I could run the tests over an hour without issue. The change fit the bug and I figured out a fix. That bad commit was: Commit 651e22f2701b "ring-buffer: Always reset iterator to reader page" This commit fixed a bug, but in the process created another one. It used the wrong value as the cached value that is used to see if things changed while an iterator was in use. This made it look like a change always happened, and could cause the iterator to go into an infinite loop" * tag 'trace-fixes-v3.17-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: ring-buffer: Fix infinite spin in reading buffer
2014-10-03Merge branch 'for-linus' of git://git.samba.org/sfrench/cifs-2.6Linus Torvalds3-8/+4
Pull cifs/smb3 fixes from Steve French: "Fix for CIFS/SMB3 oops on reconnect during readpages (3.17 regression) and for incorrectly closing file handle in symlink error cases" * 'for-linus' of git://git.samba.org/sfrench/cifs-2.6: CIFS: Fix readpages retrying on reconnects Fix problem recognizing symlinks
2014-10-03Merge tag 'md/3.17-final-fix' of git://neil.brown.name/mdLinus Torvalds1-1/+17
Pull raid5 discard fix from Neil Brown: "One fix for raid5 discard issue" * tag 'md/3.17-final-fix' of git://neil.brown.name/md: md/raid5: disable 'DISCARD' by default due to safety concerns.
2014-10-03Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linuxLinus Torvalds8-62/+65
Pull drm fixes from Dave Airlie: "Nothing too major or scary. One i915 regression fix, nouveau has a tmds regression fix, along with a regression fix for the runtime pm code for optimus laptops not restoring the display hw correctly" * 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: drm/nouveau: make sure display hardware is reinitialised on runtime resume drm/nouveau: punt fbcon resume out to a workqueue drm/nouveau: fix regression on original nv50 board drm/nv50/disp: fix dpms regression on certain boards drm/i915: Flush the PTEs after updating them before suspend
2014-10-03[SCSI] uas: disable use of blk-mq I/O pathChristoph Hellwig1-0/+7
The uas driver uses the block layer tag for USB3 stream IDs. With blk-mq we can get larger tag numbers that the queue depth, which breaks this assumption. A fix is under way for 3.18, but sits on top of large changes so can't easily be backported. Set the disable_blk_mq path so that a uas device can't easily crash the system when using blk-mq for SCSI. Signed-off-by: Christoph Hellwig <hch@lst.de> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2014-10-02Merge tag 'pm+acpi-3.17-final' of ↵Linus Torvalds4-11/+18
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm Pull ACPI and power management fixes from Rafael Wysocki: "These are three regression fixes (cpufreq core, pcc-cpufreq, i915 / ACPI) and one trivial fix for a callback return value mismatch in the cpufreq integrator driver. Specifics: - A recent cpufreq core fix went too far and introduced a regression in the system suspend code path. Fix from Viresh Kumar. - An ACPI-related commit in the i915 driver that fixed backlight problems for some Thinkpads inadvertently broke a Dell machine (in 3.16). Fix from Aaron Lu. - The pcc-cpufreq driver was broken during the 3.15 cycle by a commit that put wait_event() under a spinlock by mistake. Fix that (Rafael J Wysocki). - The return value type of integrator_cpufreq_remove() is void, but should be int. Fix from Arnd Bergmann" * tag 'pm+acpi-3.17-final' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: cpufreq: update 'cpufreq_suspended' after stopping governors ACPI / i915: Update the condition to ignore firmware backlight change request cpufreq: integrator: fix integrator_cpufreq_remove return type cpufreq: pcc-cpufreq: Fix wait_event() under spinlock
2014-10-03Merge tag 'drm-intel-fixes-2014-10-02' of ↵Dave Airlie1-1/+13
git://anongit.freedesktop.org/drm-intel into drm-fixes final regression fix for 3.17. * tag 'drm-intel-fixes-2014-10-02' of git://anongit.freedesktop.org/drm-intel: drm/i915: Flush the PTEs after updating them before suspend
2014-10-03i2c: qup: Fix order of runtime pm initializationAndy Gross1-4/+8
The runtime pm calls need to be done before populating the children via the i2c_add_adapter call. If this is not done, a child can run into issues trying to do i2c read/writes due to the pm_runtime_sync failing. Signed-off-by: Andy Gross <agross@codeaurora.org> Reviewed-by: Felipe Balbi <balbi@ti.com> Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Cc: stable@kernel.org
2014-10-03i2c: rk3x: fix 0 length write transfersAlexandru M Stan1-1/+1
i2cdetect -q was broken (everything was a false positive, and no transfers were actually being sent over i2c). The way it works is by sending a 0 length write request and checking for NACK. This patch fixes the 0 length writes and actually sends them. Reported-by: Doug Anderson <dianders@chromium.org> Signed-off-by: Alexandru M Stan <amstan@chromium.org> Tested-by: Doug Anderson <dianders@chromium.org> Tested-by: Max Schwarz <max.schwarz@online.de> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Cc: stable@kernel.org
2014-10-03Merge branches 'pm-cpufreq' and 'acpi-video'Rafael J. Wysocki4-11/+18
* pm-cpufreq: cpufreq: update 'cpufreq_suspended' after stopping governors cpufreq: integrator: fix integrator_cpufreq_remove return type cpufreq: pcc-cpufreq: Fix wait_event() under spinlock * acpi-video: ACPI / i915: Update the condition to ignore firmware backlight change request
2014-10-02Merge branch 'akpm' (fixes from Andrew Morton)Linus Torvalds6-13/+45
Merge fixes from Andrew Morton: "5 fixes" * emailed patches from Andrew Morton <akpm@linux-foundation.org>: mm: page_alloc: fix zone allocation fairness on UP perf: fix perf bug in fork() MAINTAINERS: change git URL for mpc5xxx tree mm: memcontrol: do not iterate uninitialized memcgs ocfs2/dlm: should put mle when goto kill in dlm_assert_master_handler
2014-10-02mm: page_alloc: fix zone allocation fairness on UPJohannes Weiner1-4/+3
The zone allocation batches can easily underflow due to higher-order allocations or spills to remote nodes. On SMP that's fine, because underflows are expected from concurrency and dealt with by returning 0. But on UP, zone_page_state will just return a wrapped unsigned long, which will get past the <= 0 check and then consider the zone eligible until its watermarks are hit. Commit 3a025760fc15 ("mm: page_alloc: spill to remote nodes before waking kswapd") already made the counter-resetting use atomic_long_read() to accomodate underflows from remote spills, but it didn't go all the way with it. Make it clear that these batches are expected to go negative regardless of concurrency, and use atomic_long_read() everywhere. Fixes: 81c0a2bb515f ("mm: page_alloc: fair zone allocator policy") Reported-by: Vlastimil Babka <vbabka@suse.cz> Reported-by: Leon Romanovsky <leon@leon.nu> Signed-off-by: Johannes Weiner <hannes@cmpxchg.org> Acked-by: Mel Gorman <mgorman@suse.de> Cc: <stable@vger.kernel.org> [3.12+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2014-10-02perf: fix perf bug in fork()Peter Zijlstra2-3/+6
Oleg noticed that a cleanup by Sylvain actually uncovered a bug; by calling perf_event_free_task() when failing sched_fork() we will not yet have done the memset() on ->perf_event_ctxp[] and will therefore try and 'free' the inherited contexts, which are still in use by the parent process. This is bad.. Suggested-by: Oleg Nesterov <oleg@redhat.com> Reported-by: Oleg Nesterov <oleg@redhat.com> Reported-by: Sylvain 'ythier' Hitier <sylvain.hitier@gmail.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Ingo Molnar <mingo@kernel.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2014-10-02MAINTAINERS: change git URL for mpc5xxx treeAnatolij Gustschin1-1/+1
The repository for mpc5xxx has been moved, update git URL to new location. Signed-off-by: Anatolij Gustschin <agust@denx.de> Cc: David Howells <dhowells@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2014-10-02mm: memcontrol: do not iterate uninitialized memcgsJohannes Weiner1-5/+31
The cgroup iterators yield css objects that have not yet gone through css_online(), but they are not complete memcgs at this point and so the memcg iterators should not return them. Commit d8ad30559715 ("mm/memcg: iteration skip memcgs not yet fully initialized") set out to implement exactly this, but it uses CSS_ONLINE, a cgroup-internal flag that does not meet the ordering requirements for memcg, and so the iterator may skip over initialized groups, or return partially initialized memcgs. The cgroup core can not reasonably provide a clear answer on whether the object around the css has been fully initialized, as that depends on controller-specific locking and lifetime rules. Thus, introduce a memcg-specific flag that is set after the memcg has been initialized in css_online(), and read before mem_cgroup_iter() callers access the memcg members. Signed-off-by: Johannes Weiner <hannes@cmpxchg.org> Cc: Tejun Heo <tj@kernel.org> Acked-by: Michal Hocko <mhocko@suse.cz> Cc: Hugh Dickins <hughd@google.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: <stable@vger.kernel.org> [3.12+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>