| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Add a qemu extented register range to the standard vga mmio bar.
Right nowe there are two registers: One readonly register returning the
size of the region (so we can easily add more registers there if needed)
and one endian control register, so guests (especially ppc) can flip
the framebuffer endianness as they need it.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
|
|
Add back the PCIe config capabilities on XHCI cards in non-PCIe slots,
but only for machine types before 2.1.
This fixes a migration incompatibility in the XHCI PCI devices
caused by:
058fdcf52cdbf57b67e7 - xhci: add endpoint cap on express bus only
Note that in fixing it for compatibility with older QEMUs, it breaks
compatibility with existing QEMU 2.1's on older machine types.
The status before this patch was (if it used an XHCI adapter):
machine type | source qemu
any pre-2.1 - FAIL
any 2.1... - PASS
With this patch:
machine type | source qemu
any pre-2.1 - PASS
pre-2.1 2.1... - FAIL
2.1 2.1... - PASS
A test to trigger it is to add '-device nec-usb-xhci,id=xhci,addr=0x12'
to the command line.
Cc: qemu-stable@nongnu.org
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
|
|
Add IOTLB to cache information about the translation of input-addresses. IOTLB
use a GHashTable as cache. The key of the hash table is the logical-OR of gfn
and source id after left-shifting.
Signed-off-by: Le Tan <tamlokveer@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Add context-cache to cache context-entry encountered on a page-walk. Each
VTDAddressSpace has a member of VTDContextCacheEntry which represents an entry
in the context-cache. Since devices with different bus_num and devfn have their
respective VTDAddressSpace, this will be a good way to reference the cached
entries.
Each VTDContextCacheEntry will have a context_cache_gen and the cached entry
is valid only when context_cache_gen equals IntelIOMMUState.context_cache_gen.
Signed-off-by: Le Tan <tamlokveer@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Add support for emulating Intel IOMMU according to the VT-d specification for
the q35 chipset machine. Implement the logics for DMAR (DMA remapping) without
PASID support. The emulation supports register-based invalidation and primary
fault logging.
Signed-off-by: Le Tan <tamlokveer@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
commit 868270f23d8db2cce83e4f082fe75e8625a5fbf9
acpi-build: tweak acpi migration limits
broke kernel loading with -kernel/-initrd: it doubled
the size of ACPI tables but did not reserve
enough memory.
As a result, issues on boot and halt are observed.
Fix this up by doubling reserved memory for new machine types.
Cc: qemu-stable@nongnu.org
Reported-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
pc_fw_cfg_guest_info() never does anything, because has_pci_info is
always false.
Introduced in commit f8c457b "pc: pass PCI hole ranges to Guests",
disabled in commit 9604f70 "pc: disable pci-info for 1.6", and hasn't
been enabled since. Obviously a dead end. Get of it.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
According to ICH9 spec, the MSI capability is located at 0x60. This is
important for guest drivers that do not parse the capability chain and
use absolute addresses instead.
CC: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Yet identical to 2.1.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
qemu side patch to support xen HVM direct kernel boot:
if -kernel exists, calls xen_load_linux(), which will read kernel/initrd
and add a linuxboot.bin or multiboot.bin option rom. The
linuxboot.bin/multiboot.bin will load kernel/initrd and jump to execute
kernel directly. It's working when xen uses seabios.
During this work, found the 'kvmvapic' is in option_rom list, it should
not be there in xen case. Set s->vapic_control = 0 in xen_apic_realize()
to handle that.
Signed-off-by: Chunyan Liu <cyliu@suse.com>
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Changing the ACPI table size causes migration to break, and the memory
hotplug work opened our eyes on how horribly we were breaking things in
2.0 already.
The ACPI table size is rounded to the next 4k, which one would think
gives some headroom. In practice this is not the case, because the user
can control the ACPI table size (each CPU adds 97 bytes to the SSDT and
8 to the MADT) and so some "-smp" values will break the 4k boundary and
fail to migrate. Similarly, PCI bridges add ~1870 bytes to the SSDT.
This patch concerns itself with fixing migration from QEMU 2.0. It
computes the payload size of QEMU 2.0 and always uses that one.
The previous patch shrunk the ACPI tables enough that the QEMU 2.0 size
should always be enough; non-AML tables can change depending on the
configuration (especially MADT, SRAT, HPET) but they remain the same
between QEMU 2.0 and 2.1, so we only compute our padding based on the
sizes of the SSDT and DSDT.
Migration from QEMU 1.7 should work for guests that have a number of CPUs
other than 12, 13, 14, 54, 55, 56, 97, 98, 139, 140. It was already
broken from QEMU 1.7 to QEMU 2.0 in the same way, though.
Even with this patch, QEMU 1.7 and 2.0 have two different ideas of
"-M pc-i440fx-2.0" when there are PCI bridges. Igor sent a patch to
adopt the QEMU 1.7 definition. I think distributions should apply
it if they move directly from QEMU 1.7 to 2.1+ without ever packaging
version 2.0.
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
The property name is "prog_if", not "prof_if".
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reported-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
For each compat property on PC_Q35_COMPAT_*, there are only two
possibilities:
* If the device is never instantiated when using a machine other than
pc-q35, then the compat property can be safely added to
PC_COMPAT_*;
* If the device can be instantiated when using a machine other than
pc-q35, that means the other machines also need the compat property
to be set.
That means we don't need separate PC_Q35_COMPAT_* macros at all, today.
The hpet.hpet-intcap case is interesting: piix and q35 do have something
that emulates different defaults, but the machine-specific default is
applied _after_ compat_props are applied, by simply checking if the
property is zero (which is the real default on the hpet code).
The hpet.hpet-intcap=0x4 compat property can (should?) be applied to
piix too, because 0x4 was the default on both piix and q35 before the
hpet-intcap property was introduced.
Now, if one day we change the default HPET intcap on one of the PC
machine-types again, we may want to introduce PC_{Q35,I440FX}_COMPAT
macros. But while we don't need that, we can keep the code simple.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Cc: Liu Ping Fan <pingfank@linux.vnet.ibm.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
This is a pc & q35 only machine opt.
If you add enough PCI devices then all mmio for them will not fit
below 4G which may not be the layout the user wanted. This allows
you to increase the below 4G address space that PCI devices can use
(aka decrease ram below 4G) and therefore in more cases not have any
mmio that is above 4G.
For example using "-machine pc,max-ram-below-4g=2G" on the command
line will limit the amount of ram that is below 4G to 2G.
Note: this machine option cannot be used to increase the amount
of ram below 4G.
Signed-off-by: Don Slutz <dslutz@verizon.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
MST: fix 32 bit
|
|
It is needed by hot-unplug in order to get an indication
from the OS when the device can be physically detached.
Signed-off-by: Marcel Apfelbaum <marcel.a@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
pc,pci,virtio,hotplug fixes, enhancements
numa work by Hu Tao and others
memory hotplug by Igor
vhost-user by Nikolay, Antonios and others
guest virtio announcements by Jason
qtest fixes by Sergey
qdev hotplug fixes by Paolo
misc other fixes mostly by myself
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
* remotes/mst/tags/for_upstream: (109 commits)
numa: use RAM_ADDR_FMT with ram_addr_t
qapi/string-output-visitor: fix bugs
tests: simplify code
qapi: fix input visitor bugs
acpi: rephrase comment
qmp: add ACPI_DEVICE_OST event handling
qmp: add query-acpi-ospm-status command
acpi: implement ospm_status() method for PIIX4/ICH9_LPC devices
acpi: introduce TYPE_ACPI_DEVICE_IF interface
qmp: add query-memory-devices command
numa: handle mmaped memory allocation failure correctly
pc: acpi: do not hardcode preprocessor
qmp: clean out whitespace
qdev: recursively unrealize devices when unrealizing bus
qdev: reorganize error reporting in bus_set_realized
qapi: fix build on glib < 2.28
qapi: make string output visitor parse int list
qapi: make string input visitor parse int list
tests: fix memory leak in test of string input visitor
hmp: add info memdev
...
Conflicts:
include/hw/i386/pc.h
[PMM: fixed minor conflict in pc.h]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Hu Tao <hutao@cn.fujitsu.com>
Reviewed-By: Igor Mammedov <imammedo@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
It's hard to track all mac addresses and their configurations (e.g
vlan or ipv6) in qemu. Without this information, it's impossible to
build proper garp packet after migration. The only possible solution
to this is let guest (who knows all configurations) to do this.
So, this patch introduces a new readonly config status bit of virtio-net,
VIRTIO_NET_S_ANNOUNCE which is used to notify guest to announce
presence of its link through config update interrupt.When guest has
done the announcement, it should ack the notification through
VIRTIO_NET_CTRL_ANNOUNCE_ACK cmd. This feature is negotiated by a new
feature bit VIRTIO_NET_F_ANNOUNCE (which has already been supported by
Linux guest).
During load, a counter of announcing rounds is set so that after the vm is
running it can trigger rounds of config interrupts to notify the guest to build
and send the correct garps.
Cc: Liuyongan <liuyongan@huawei.com>
Cc: Amos Kong <akong@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Names with spaces in them are nasty, let's not go there.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
... it will be used by acpi-build code and by unit tests
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
the link will used later to access device implementing
ACPI functions instead of adhoc lookup in QOM tree.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Add memory hotplug initialization/handling to ICH9 LPC device
and enable it by default for post 2.0 machine types
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Add memory hotplug initialization/handling to PIIX4_PM device
and enable it by default for post 2.0 machine types
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
MST: resolve conflict in pc.h
|
|
that will perform mapping of PC_DIMM device into guest's RAM address space
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
'etc/reserved-memory-end' will allow QEMU to tell BIOS where PCI
BARs mapping could safely start in high memory.
Allowing BIOS to start mapping 64-bit PCI BARs at address where it
wouldn't conflict with other mappings QEMU might place before it.
That permits QEMU to reserve extra address space before
64-bit PCI hole for memory hotplug.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
initialize and map hotplug memory address space container
into guest's RAM address space.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
it will be used for PC specific options/variables
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Store the request and response headers by value, and let
virtio_scsi_parse_req check that there is only one of datain
and dataout.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
pc,pci,virtio,qdev fixes, tests
new tests for SMBIOS
SMBIOS fixes
pc, pci fixes
qdev patches stayed on list for a month with no review,
as I told people on KVM forum I'm merging stuch patches
if they look fine.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
* remotes/mst/tags/for_upstream:
qdev: Add test of qdev_prop_check_global
qdev: Display warning about unused -global
tests: add smbios testing
tests: rename acpi-test to bios-tables-test
virtio-balloon: return empty data when no stats are available
pcie_host: Turn pcie_host_init() into an instance_init
SMBIOS: Fix type 17 field sizes
SMBIOS: Update Type 0 struct generator for machines >= 2.1
SMBIOS: Fix endian-ness when populating multi-byte fields
serial-pci: Set prog interface field of pci config to 16550 compatible
Conflicts:
include/hw/i386/pc.h
[PMM: fixed trivial conflict in pc.h]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
|
|
Fields for configured_clock_speed and various voltage values
introduced in spec v2.7+ should be "word", i.e. 16 bits.
Reported-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Gabriel Somlo <somlo@cmu.edu>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Update how type 0 (bios info) structures are generated, as follows:
- convert bios_characteristics field to uin64_t (instead of
uint8_t[8]), as described in the current smbios spec (v2.8)
- enable "virtual machine" bit in bios_characteristics_extension_bits
- add command line option to enable "uefi supported" bit in
bios_characteristics_extension_bits
These updates should make this optional structure more useful when
used with edk2/ovmf. Only pc machines >= 2.1 are affected, and only
when a type 0 structure is explicitly specified on the command line.
Signed-off-by: Gabriel Somlo <somlo@cmu.edu>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
|
|
Add "version" property to local apic, and have it default to
0x14 for pc machines starting at 2.1. For compatibility with
previous releases, pc machines up to 2.0 will have their local
apic version set to 0x11.
Signed-off-by: Gabriel L. Somlo <somlo@cmu.edu>
Acked-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Add the "boilerplate" necessary for subsequent patches to
simply drop in compat_props for pc machines 2.0 and older.
This patch contains no functional changes.
Signed-off-by: Gabriel Somlo <somlo@cmu.edu>
Acked-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Build an aggregate set of smbios tables and an entry point structure.
Insert tables and entry point into fw_cfg respectively under
"etc/smbios/smbios-tables" and "etc/smbios/smbios-anchor".
Machine types <= 2.0 will for now continue using field-by-field
overrides to SeaBIOS defaults, but for machine types 2.1 and up we
expect the BIOS to look for and use the aggregate tables generated
by this patch.
Signed-off-by: Gabriel Somlo <somlo@cmu.edu>
[ kraxel: fix 32bit build ]
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
|
|
Replace existing smbios_check_collision() functionality with
a pair of bitmaps: have_binfile_bitmap and have_fields_bitmap.
Bits corresponding to each smbios type are set by smbios_entry_add(),
which also uses the bitmaps to ensure that binary blobs and field
values are never accepted for the same type.
These bitmaps will also be used in the future to decide whether
or not to build a full table for a given smbios type.
Signed-off-by: Gabriel Somlo <somlo@cmu.edu>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
|
|
Add definitions for smbios entry point (anchor), and for type 2
(base board) structure which is required by some versions of OS X.
Remove definition for type 20 (memory device mapped address)
structure, which is no longer required as of smbios spec v2.5.
Update all other structure definitions to bring them into
compliance with smbios spec v2.8.
This patch contains no functional changes.
Signed-off-by: Gabriel Somlo <somlo@cmu.edu>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
|
|
Rename the following symbols:
- smbios_set_type1_defaults() to the more general smbios_set_defaults();
- bool smbios_type1_defaults to the more general smbios_defaults;
- smbios_get_table() to smbios_get_table_legacy();
This patch contains no functional changes.
Signed-off-by: Gabriel Somlo <somlo@cmu.edu>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
|
|
Add the following two functions:
- e820_get_num_entries() - query the size of the e820 table
- e820_get_entry() - grab an entry matching a given set of criteria
This interface is currently necessary for creating type 19
(memory array mapped address) structures in smbios.
Signed-off-by: Gabriel Somlo <somlo@cmu.edu>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
|
|
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
|
|
The ram_below_4g value will be useful in other places, such as the ACPI
table code, and other code that currently requires passing
below_4g_mem_size around in function arguments.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Add support for acpi pci hotplug using the
new infrastructure.
PIIX4 legacy interface is maintained as is for
machine types 1.7 and older.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
This patch adds support for special usb descriptors used by microsoft
windows. They allow more fine-grained control over driver binding and
adding entries to the registry for configuration.
As this is a guest-visible change the "msos-desc" compat property
has been added to turn this off for 1.7 + older
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
|
|
acpi,pci,pc,fedora,virtio fixes and enhancements
This includes some Preparatory patches for cpu hotplug for q25 and memory
hotplug by Igor, tests and memory mapping change
by Laszlo and pci reset cleanup by Paolo.
There are also some fixes for fedora and virtio:
included here since they are test blockers for me.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Mon 23 Dec 2013 08:07:18 AM PST using RSA key ID D28D5469
# gpg: Can't check signature: public key not found
* mst/tags/for_anthony:
target-arm: fix build with gcc 4.8.2
virtio: add back call to virtio_bus_device_unplugged
piix: fix 32bit pci hole
qdev: switch reset to post-order
qdev: allow both pre- and post-order vists in qdev walking functions
pci: clean up resetting of IRQs
pci: do not export pci_bus_reset
ACPI/DSDT-CPU: cleanup bogus comment
ACPI: Q35 DSDT: fix CPU hotplug GPE0.2 handler
acpi: ich9: allow guest to clear SCI rised by GPE
acpi: factor out common pm_update_sci() into acpi core
acpi: piix4: remove not needed GPE0 mask
i440fx-test: verify firmware under 4G and 1M, both -bios and -pflash
i440fx-test: generate temporary firmware blob
i440fx-test: give each GTest case its own qtest
i440fx-test: qtest_start() should be paired with qtest_end()
hw/i386/pc_sysfw: support two flash drives
pc_piix: document gigabyte_align
piix: gigabyte alignment for ram
Message-id: 1387815007-1272-1-git-send-email-mst@redhat.com
Signed-off-by: Anthony Liguori <aliguori@amazon.com>
|
|
Convert 'init' function to QOM's 'realize' for ioapic and kvm-ioapic.
Change variable 'ioapic_no' from static to global. Then we can drop
the 'instance_no' function argument.
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
|
|
Convert 'init' function to QOM's 'realize' for apic, kvm/apic and
xen/xen_apic.
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
|
|
Make the 32bit pci hole start at end of ram, so all possible address
space is covered.
We used to try and make addresses aligned so they are easier to cover
with MTRRs, but since they are cosmetic on KVM, this is probably not
worth worrying about.
Of course the firmware can use less than that. Leaving space unused is
no problem, mapping pci bars outside the hole causes problems though.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Owning to some different hardware design, piix and q35 need
different compat. So making them diverge.
On q35, IRQ2/8 can be reserved for hpet timer 0/1. And pin 16~23
can be assigned to hpet as guest chooses. So we introduce intcap
property to do that.
Consider the compat and piix/q35, we finally have the following
value for intcap: For piix, hpet's intcap is hard coded as IRQ2.
For pc-q35-1.7 and earlier, we use IRQ2 for compat reason. Otherwise
IRQ2, IRQ8, and IRQ16~23 are allowed.
Signed-off-by: Liu Ping Fan <pingfank@linux.vnet.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
