summaryrefslogtreecommitdiff
path: root/include
AgeCommit message (Collapse)AuthorFilesLines
2016-07-21kvm-irqchip: do explicit commit when update irqPeter Xu1-1/+1
In the past, we are doing gsi route commit for each irqchip route update. This is not efficient if we are updating lots of routes in the same time. This patch removes the committing phase in kvm_irqchip_update_msi_route(). Instead, we do explicit commit after all routes updated. Signed-off-by: Peter Xu <peterx@redhat.com> Reviewed-by: Paolo Bonzini <pbonzini@redhat.com> Reviewed-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
2016-07-21kvm-irqchip: x86: add msi route notify fnPeter Xu1-0/+2
One more IEC notifier is added to let msi routes know about the IEC changes. When interrupt invalidation happens, all registered msi routes will be updated for all PCI devices. Since both vfio and vhost are possible gsi route consumers, this patch will go one step further to keep them safe in split irqchip mode and when irqfd is enabled. Reviewed-by: Paolo Bonzini <pbonzini@redhat.com> [move trace-events lines into target-i386/trace-events] Signed-off-by: Peter Xu <peterx@redhat.com> Reviewed-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
2016-07-21kvm-irqchip: i386: add hook for add/remove virqPeter Xu1-0/+6
Adding two hooks to be notified when adding/removing msi routes. There are two kinds of MSI routes: - in kvm_irqchip_add_irq_route(): before assigning IRQFD. Used by vhost, vfio, etc. - in kvm_irqchip_send_msi(): when sending direct MSI message, if direct MSI not allowed, we will first create one MSI route entry in the kernel, then trigger it. This patch only hooks the first one (irqfd case). We do not need to take care for the 2nd one, since it's only used by QEMU userspace (kvm-apic) and the messages will always do in-time translation when triggered. While we need to note them down for the 1st one, so that we can notify the kernel when cache invalidation happens. Also, we do not hook IOAPIC msi routes (we have explicit notifier for IOAPIC to keep its cache updated). We only need to care about irqfd users. Signed-off-by: Peter Xu <peterx@redhat.com> Reviewed-by: Paolo Bonzini <pbonzini@redhat.com> Reviewed-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
2016-07-21kvm-irqchip: simplify kvm_irqchip_add_msi_routePeter Xu1-1/+12
Changing the original MSIMessage parameter in kvm_irqchip_add_msi_route into the vector number. Vector index provides more information than the MSIMessage, we can retrieve the MSIMessage using the vector easily. This will avoid fetching MSIMessage every time before adding MSI routes. Meanwhile, the vector info will be used in the coming patches to further enable gsi route update notifications. Signed-off-by: Peter Xu <peterx@redhat.com> Reviewed-by: Paolo Bonzini <pbonzini@redhat.com> Reviewed-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
2016-07-21intel_iommu: add SID validation for IRPeter Xu1-0/+17
This patch enables SID validation. Invalid interrupts will be dropped. Signed-off-by: Peter Xu <peterx@redhat.com> Reviewed-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
2016-07-21intel_iommu: Add support for Extended Interrupt ModeJan Kiszka1-0/+1
As neither QEMU nor KVM support more than 255 CPUs so far, this is simple: we only need to switch the destination ID translation in vtd_remap_irq_get if EIME is set. Once CFI support is there, it will have to take EIM into account as well. So far, nothing to do for this. This patch allows to use x2APIC in split irqchip mode of KVM. Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com> [use le32_to_cpu() to retrieve dest_id] Signed-off-by: Peter Xu <peterx@redhat.com> Reviewed-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
2016-07-21ioapic: register IOMMU IEC notifier for ioapicPeter Xu1-0/+2
Let IOAPIC the first consumer of x86 IOMMU IEC invalidation notifiers. This is only used for split irqchip case, when vIOMMU receives IR invalidation requests, IOAPIC will be notified to update kernel irq routes. For simplicity, we just update all IOAPIC routes, even if the invalidated entries are not IOAPIC ones. Since now we are creating IOMMUs using "-device" parameter, IOMMU device will be created after IOAPIC. We need to do the registration after machine done by leveraging machine_done notifier. Signed-off-by: Peter Xu <peterx@redhat.com> Reviewed-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
2016-07-21x86-iommu: introduce IEC notifiersPeter Xu1-0/+40
This patch introduces x86 IOMMU IEC (Interrupt Entry Cache) invalidation notifier list. When vIOMMU receives IEC invalidate request, all the registered units will be notified with specific invalidation requests. Intel IOMMU is the first provider that generates such a event. Signed-off-by: Peter Xu <peterx@redhat.com> Reviewed-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
2016-07-21intel_iommu: add support for split irqchipPeter Xu2-0/+6
In split irqchip mode, IOAPIC is working in user space, only update kernel irq routes when entry changed. When IR is enabled, we directly update the kernel with translated messages. It works just like a kernel cache for the remapping entries. Since KVM irqfd is using kernel gsi routes to deliver interrupts, as long as we can support split irqchip, we will support irqfd as well. Also, since kernel gsi routes will cache translated interrupts, irqfd delivery will not suffer from any performance impact due to IR. And, since we supported irqfd, vhost devices will be able to work seamlessly with IR now. Logically this should contain both vhost-net and vhost-user case. Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> [move trace-events lines into target-i386/trace-events] Signed-off-by: Peter Xu <peterx@redhat.com> Reviewed-by: Paolo Bonzini <pbonzini@redhat.com> Reviewed-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
2016-07-21q35: ioapic: add support for emulated IOAPIC IRPeter Xu3-0/+6
This patch translates all IOAPIC interrupts into MSI ones. One pseudo ioapic address space is added to transfer the MSI message. By default, it will be system memory address space. When IR is enabled, it will be IOMMU address space. Currently, only emulated IOAPIC is supported. Idea suggested by Jan Kiszka and Rita Sinha in the following patch: https://lists.gnu.org/archive/html/qemu-devel/2016-03/msg01933.html Signed-off-by: Peter Xu <peterx@redhat.com> Reviewed-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
2016-07-20intel_iommu: Add support for PCI MSI remapPeter Xu1-0/+66
This patch enables interrupt remapping for PCI devices. To play the trick, one memory region "iommu_ir" is added as child region of the original iommu memory region, covering range 0xfeeXXXXX (which is the address range for APIC). All the writes to this range will be taken as MSI, and translation is carried out only when IR is enabled. Idea suggested by Paolo Bonzini. Signed-off-by: Peter Xu <peterx@redhat.com> Reviewed-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
2016-07-20intel_iommu: define several structs for IOMMU IRPeter Xu1-0/+74
Several data structs are defined to better support the rest of the patches: IRTE to parse remapping table entries, and IOAPIC/MSI related structure bits to parse interrupt entries to be filled in by guest kernel. Signed-off-by: Peter Xu <peterx@redhat.com> Reviewed-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
2016-07-20intel_iommu: define interrupt remap table addr registerPeter Xu1-0/+5
Defined Interrupt Remap Table Address register to store IR table pointer. Also, do proper handling on global command register writes to store table pointer and its size. One more debug flag "DEBUG_IR" is added for interrupt remapping. Signed-off-by: Peter Xu <peterx@redhat.com> Reviewed-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
2016-07-20acpi: add DMAR scope definition for root IOAPICPeter Xu2-0/+21
To enable interrupt remapping for intel IOMMU device, each IOAPIC device in the system reported via ACPI MADT must be explicitly enumerated under one specific remapping hardware unit. This patch adds the root-complex IOAPIC into the default DMAR device. Please refer to VT-d spec 8.3.1.1 for more information. Signed-off-by: Peter Xu <peterx@redhat.com> Reviewed-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
2016-07-20acpi: enable INTR for DMAR report structurePeter Xu1-0/+2
In ACPI DMA remapping report structure, enable INTR flag when specified. Signed-off-by: Peter Xu <peterx@redhat.com> Reviewed-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
2016-07-20x86-iommu: introduce "intremap" propertyPeter Xu1-0/+1
Adding one property for intel-iommu devices to specify whether we should support interrupt remapping. By default, IR is disabled. To enable it, we should use (take Intel IOMMU as example): -device intel_iommu,intremap=on This property can be shared by Intel and future AMD IOMMUs. Signed-off-by: Peter Xu <peterx@redhat.com> Reviewed-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
2016-07-20x86-iommu: provide x86_iommu_get_defaultPeter Xu1-0/+6
Instead of searching the device tree every time, one static variable is declared for the default system x86 IOMMU device. Signed-off-by: Peter Xu <peterx@redhat.com> Reviewed-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
2016-07-20intel_iommu: rename VTD_PCI_DEVFN_MAX to x86-iommuPeter Xu2-1/+2
Signed-off-by: Peter Xu <peterx@redhat.com> Reviewed-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
2016-07-20x86-iommu: introduce parent classPeter Xu2-1/+48
Introducing parent class for intel-iommu devices named "x86-iommu". This is preparation work to abstract shared functionalities out from Intel and AMD IOMMUs. Currently, only the parent class is introduced. It does nothing yet. Signed-off-by: Peter Xu <peterx@redhat.com> Reviewed-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
2016-07-19disas: Fix ATTRIBUTE_UNUSED define clash with ALSA headersPeter Maydell1-0/+2
disas/bfd.h defines ATTRIBUTE_UNUSED, but unfortunately the ALSA system headers also define this macro, which means that you can get a compilation failure if building with ALSA and any files happen to include the alsa headers before bfd.h rather than the other way around. This is unfortunate namespace pollution by the ALSA headers but we can work around it. Add an #ifndef guard to bfd.h and remove the unnecessary extra definition in disas/arm.c to fix this. Reported-by: BALATON Zoltan <balaton@eik.bme.hu> Signed-off-by: Peter Maydell <peter.maydell@linaro.org> Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com> Message-id: 1468937076-21503-1-git-send-email-peter.maydell@linaro.org
2016-07-19Merge remote-tracking branch 'remotes/bonzini/tags/for-upstream' into stagingPeter Maydell1-0/+3
* two old patches from prospective GSoC students * i386 -kernel device tree support * Coverity fix * memory usage improvement from Peter * checkpatch fix * g_path_get_dirname cleanup * caching of block status for iSCSI # gpg: Signature made Tue 19 Jul 2016 07:43:41 BST # gpg: using RSA key 0xBFFBD25F78C7AE83 # gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>" # gpg: aka "Paolo Bonzini <pbonzini@redhat.com>" # Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4 E2F7 7E15 100C CD36 69B1 # Subkey fingerprint: F133 3857 4B66 2389 866C 7682 BFFB D25F 78C7 AE83 * remotes/bonzini/tags/for-upstream: target-i386: Remove redundant HF_SOFTMMU_MASK block/iscsi: allow caching of the allocation map block/iscsi: fix rounding in iscsi_allocationmap_set Move README to markdown cpu-exec: Move down some declarations in cpu_exec() exec: avoid realloc in phys_map_node_reserve checkpatch: consider git extended headers valid patches megasas: remove useless check for cmd->frame compiler: never omit assertions if using a static analysis tool hw/i386: add device tree support Changed malloc to g_malloc, free to g_free in bsd-user/qemu.h use g_path_get_dirname instead of dirname Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2016-07-19Merge remote-tracking branch 'remotes/jnsnow/tags/ide-pull-request' into stagingPeter Maydell1-0/+5
# gpg: Signature made Mon 18 Jul 2016 23:53:15 BST # gpg: using RSA key 0x7DEF8106AAFC390E # gpg: Good signature from "John Snow (John Huston) <jsnow@redhat.com>" # Primary key fingerprint: FAEB 9711 A12C F475 812F 18F2 88A9 064D 1835 61EB # Subkey fingerprint: F9B7 ABDB BCAC DF95 BE76 CBD0 7DEF 8106 AAFC 390E * remotes/jnsnow/tags/ide-pull-request: block: ignore flush requests when storage is clean tests: in IDE and AHCI tests perform DMA write before flushing ide: set retry_unit for PIO and FLUSH requests ide: refactor retry_unit set and clear into separate function Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2016-07-19Merge remote-tracking branch 'remotes/stefanha/tags/tracing-pull-request' ↵Peter Maydell2-1/+6
into staging # gpg: Signature made Mon 18 Jul 2016 22:59:55 BST # gpg: using RSA key 0x9CA4ABB381AB73C8 # gpg: Good signature from "Stefan Hajnoczi <stefanha@redhat.com>" # gpg: aka "Stefan Hajnoczi <stefanha@gmail.com>" # Primary key fingerprint: 8695 A8BF D3F9 7CDA AC35 775A 9CA4 ABB3 81AB 73C8 * remotes/stefanha/tags/tracing-pull-request: trace: Add QAPI/QMP interfaces to query and control per-vCPU tracing state trace: Allow event name pattern in "info trace-events" trace: Conditionally trace events based on their per-vCPU state trace: Add per-vCPU tracing states for events with the 'vcpu' property trace: Cosmetic changes on fast-path tracing disas: Remove unused macro '_' trace: Identify events with the 'vcpu' property trace: [bsd-user] Commandline arguments to control tracing trace: [linux-user] Commandline arguments to control tracing Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2016-07-18block: ignore flush requests when storage is cleanEvgeny Yakovlev1-0/+5
Some guests (win2008 server for example) do a lot of unnecessary flushing when underlying media has not changed. This adds additional overhead on host when calling fsync/fdatasync. This change introduces a write generation scheme in BlockDriverState. Current write generation is checked against last flushed generation to avoid unnessesary flushes. The problem with excessive flushing was found by a performance test which does parallel directory tree creation (from 2 processes). Results improved from 0.424 loops/sec to 0.432 loops/sec. Each loop creates 10^3 directories with 10 files in each. This affected some blkdebug testcases that were expecting error logs from failure-injected flushes which are now skipped entirely (tests 026 071 089). This also affects the performance of block jobs and thus BLOCK_JOB_READY events for driver-mirror and active block-commit commands now arrives faster, before QMP send successfully returns to caller (tests 141 144). Signed-off-by: Evgeny Yakovlev <eyakovlev@virtuozzo.com> Signed-off-by: Denis V. Lunev <den@openvz.org> Reviewed-by: Paolo Bonzini <pbonzini@redhat.com> Message-id: 1468870792-7411-5-git-send-email-den@openvz.org CC: Kevin Wolf <kwolf@redhat.com> CC: Max Reitz <mreitz@redhat.com> CC: Stefan Hajnoczi <stefanha@redhat.com> CC: Fam Zheng <famz@redhat.com> CC: John Snow <jsnow@redhat.com> Signed-off-by: John Snow <jsnow@redhat.com>
2016-07-18trace: Add per-vCPU tracing states for events with the 'vcpu' propertyLluís Vilanova1-0/+6
Each vCPU gets a 'trace_dstate' bitmap to control the per-vCPU dynamic tracing state of events with the 'vcpu' property. Signed-off-by: Lluís Vilanova <vilanova@ac.upc.edu> Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
2016-07-18disas: Remove unused macro '_'Lluís Vilanova1-1/+0
Eliminates a future compilation error when UI code includes the tracing headers (indirectly pulling "disas/bfd.h" through "qom/cpu.h") and GLib's i18n '_' macro. Signed-off-by: Lluís Vilanova <vilanova@ac.upc.edu> Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
2016-07-18aio-posix: remove useless parameterCao jin1-1/+1
Parameter **errp of aio_context_setup() is useless, remove it and clean up the related code. Cc: Stefan Hajnoczi <stefanha@redhat.com> Cc: Fam Zheng <famz@redhat.com> Cc: Eric Blake <eblake@redhat.com> Signed-off-by: Cao jin <caoj.fnst@cn.fujitsu.com> Reviewed-by: Eric Blake <eblake@redhat.com> Message-id: 1468578524-23433-1-git-send-email-caoj.fnst@cn.fujitsu.com Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
2016-07-18linux-aio: share one LinuxAioState within an AioContextPaolo Bonzini2-0/+81
This has better performance because it executes fewer system calls and does not use a bottom half per disk. Originally proposed by Ming Lei. [Changed #include "raw-aio.h" to "block/raw-aio.h" in win32-aio.c to fix build error as reported by Peter Maydell <peter.maydell@linaro.org>. --Stefan] Acked-by: Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Message-id: 1467650000-51385-1-git-send-email-pbonzini@redhat.com Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com> squash! linux-aio: share one LinuxAioState within an AioContext
2016-07-17compiler: never omit assertions if using a static analysis toolPaolo Bonzini1-0/+3
Assertions help both Coverity and the clang static analyzer avoid false positives, but on the other hand both are confused when the condition is compiled as (void)(x != FOO). Always expand assertion macros when using Coverity or clang, through a new QEMU_STATIC_ANALYSIS preprocessor symbol. This fixes a couple false positives in TCG. Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2016-07-14Merge remote-tracking branch ↵Peter Maydell4-1/+16
'remotes/pmaydell/tags/pull-target-arm-20160714' into staging target-arm queue: * add virtio-mmio transport base address to device path (avoid an assertion failure with multiple virtio-scsi-devices) * revert hw/ptimer commit 5a50307 which causes regressions on SPARC guests * use Neon to accelerate zero-page checking on AArch64 hosts * set the MPIDR for TCG to match how KVM does it (and fit with GICv2/GICv3 restrictions on SGI target lists) * add some missing AArch32 TLBI hypervisor TLB operations * m25p80: Fix QIOR/DIOR handling for Winbond * hw/misc: fix typo in Aspeed SCU hw-strap2 property name * ast2400: pretend DMAs are done for U-boot * ast2400: some minor code cleanups # gpg: Signature made Thu 14 Jul 2016 17:21:30 BST # gpg: using RSA key 0x3C2525ED14360CDE # gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>" # gpg: aka "Peter Maydell <pmaydell@gmail.com>" # gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>" # Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE * remotes/pmaydell/tags/pull-target-arm-20160714: ast2400: externalize revision numbers ast2400: pretend DMAs are done for U-boot ast2400: replace aspeed_smc_is_implemented() hw/misc: fix typo in Aspeed SCU hw-strap2 property name m25p80: Fix QIOR/DIOR handling for Winbond target-arm: Add missed AArch32 TLBI sytem registers hw/arm/virt: tcg: adjust MPIDR like KVM gic: provide defines for v2/v3 targetlist sizes target-arm: Use Neon for zero checking Revert "hw/ptimer: Perform counter wrap around if timer already expired" virtio-mmio: format transport base address in BusClass.get_dev_path Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2016-07-14ast2400: externalize revision numbersCédric Le Goater1-0/+5
AST2400_A0_SILICON_REV is defined twice. Fix this by including the definition in the header file as well as the routine to check if a silicon revision is supported. It will useful to reuse in other controllers. Let's add also AST2500_A0_SILICON_REV for future use. Signed-off-by: Cédric Le Goater <clg@kaod.org> Message-id: 1467994016-11678-5-git-send-email-clg@kaod.org Reviewed-by: Peter Maydell <peter.maydell@linaro.org> Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2016-07-14gic: provide defines for v2/v3 targetlist sizesAndrew Jones2-0/+6
Signed-off-by: Andrew Jones <drjones@redhat.com> Message-id: 1467378129-23302-2-git-send-email-drjones@redhat.com Reviewed-by: Peter Maydell <peter.maydell@linaro.org> Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2016-07-14virtio-mmio: format transport base address in BusClass.get_dev_pathLaszlo Ersek1-1/+5
At the moment the following QEMU command line triggers an assertion failure (minimal reproducer by Cole): qemu-system-aarch64 \ -machine virt-2.6,accel=tcg \ -nodefaults \ -no-user-config \ -nographic -monitor stdio \ -device virtio-scsi-device,id=scsi0 \ -device virtio-scsi-device,id=scsi1 \ -drive file=foo.img,format=raw,if=none,id=d0 \ -device scsi-hd,bus=scsi0.0,drive=d0 \ -drive file=foo.img,format=raw,if=none,id=d1 \ -device scsi-hd,bus=scsi1.0,drive=d1 qemu-system-aarch64: migration/savevm.c:615: vmstate_register_with_alias_id: Assertion `!se->compat || se->instance_id == 0' failed. The reason is that the vmstate sections for the two scsi-hd devices are not uniquely identifiable by name. The direct parent buses of the scsi-hd devices -- scsi0.0 and scsi1.0 -- support the BusClass.get_dev_path member function. scsibus_get_dev_path() formats a device path prefix with the help of its topologically parent bus, and then appends the chan:id:lun triplet to it. For both scsi-hd devices, this triplet is 0:0:0. (Here we use "device path" in the QEMU migration sense, for vmstate section identification, not in the OFW or UEFI device path senses.) The virtio-scsi HBA is plugged into the virtio-mmio bus (implemented by the internal VirtIOMMIOProxy device). This bus class (TYPE_VIRTIO_MMIO_BUS) inherits, as its get_dev_path() member function, the virtio_bus_get_dev_path() method from its parent class (TYPE_VIRTIO_BUS). virtio_bus_get_dev_path() does not format any kind of device address on its own; "virtio addresses" are transport-specific. Therefore virtio_bus_get_dev_path() asks the topologically parent bus of the proxy object (implementing the specific virtio transport) to format the address of the proxy object. (For virtio-pci devices (where the proxy is an instance of VirtIOPCIProxy, plugged into a PCI bus), this ends up in pcibus_get_dev_path().) However, VirtIOMMIOProxy is usually (in practice: always) plugged into "main-system-bus", the singleton TYPE_SYSTEM_BUS object. This BusClass does not support formatting QEMU vmstate device paths at all (as SysBusDevice objects can have zero or more IO ports and zero or more MMIO regions). Hence the formatting request delegated from virtio_bus_get_dev_path() gets answered with NULL. The end result is that the two scsi-hd devices end up with the same device path "0:0:0", which triggers the assert. We can solve this by recognizing that virtio-mmio transports are distinguished from each other by their base addresses in MMIO address space. Implement virtio_mmio_bus_get_dev_path() as follows: (1) The virtio device whose devpath is to be formatted resides on a virtio-mmio bus that is implemented by a VirtIOMMIOProxy object. Ask the parent bus of VirtIOMMIOProxy to format the device path of VirtIOMMIOProxy, as a path prefix. (This is identical to what virtio_bus_get_dev_path() does.) (2) Append the base address of VirtIOMMIOProxy to the device path, such as: - virtio-mmio@000000000a003e00, - virtio-mmio@000000000a003c00. Given that these device paths are placed in the migration stream, step (2) above, if done unconditionally, would break migration. So make that step conditional on a new VirtIOMMIOProxy property, which is enabled for 2.7 machine types and later. Cc: "Michael S. Tsirkin" <mst@redhat.com> Cc: Cole Robinson <crobinso@redhat.com> Cc: Dr. David Alan Gilbert <dgilbert@redhat.com> Cc: Kevin Zhao <kevin.zhao@linaro.org> Cc: Peter Maydell <peter.maydell@linaro.org> Cc: Tom Hanson <thomas.hanson@linaro.org> Reported-by: Kevin Zhao <kevin.zhao@linaro.org> Reviewed-by: Andrew Jones <drjones@redhat.com> Signed-off-by: Laszlo Ersek <lersek@redhat.com> Message-id: 1467739394-28357-1-git-send-email-lersek@redhat.com Fixes: https://bugs.launchpad.net/qemu/+bug/1594239 Signed-off-by: Laszlo Ersek <lersek@redhat.com> Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2016-07-14Merge remote-tracking branch 'remotes/bonzini/tags/for-upstream-fwcfg' into ↵Peter Maydell2-0/+5
staging * Updated fw_cfg option ROM to include DMA support # gpg: Signature made Thu 14 Jul 2016 14:51:06 BST # gpg: using RSA key 0xBFFBD25F78C7AE83 # gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>" # gpg: aka "Paolo Bonzini <pbonzini@redhat.com>" # Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4 E2F7 7E15 100C CD36 69B1 # Subkey fingerprint: F133 3857 4B66 2389 866C 7682 BFFB D25F 78C7 AE83 * remotes/bonzini/tags/for-upstream-fwcfg: Add optionrom compatible with fw_cfg DMA version Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2016-07-14Add optionrom compatible with fw_cfg DMA versionMarc Marí2-0/+5
This optionrom is based on linuxboot.S. Signed-off-by: Marc Marí <markmb@redhat.com> Signed-off-by: Richard W.M. Jones <rjones@redhat.com> Message-Id: <1464027093-24073-2-git-send-email-rjones@redhat.com> [Add -fno-toplevel-reorder, support clang without -m16. - Paolo] Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2016-07-14Merge remote-tracking branch 'remotes/bonzini/tags/for-upstream' into stagingPeter Maydell6-6/+23
* SCSI scanner support * fixes to qemu-char and net exit * FreeBSD fixes * Other small bugfixes # gpg: Signature made Wed 13 Jul 2016 12:30:11 BST # gpg: using RSA key 0xBFFBD25F78C7AE83 # gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>" # gpg: aka "Paolo Bonzini <pbonzini@redhat.com>" # Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4 E2F7 7E15 100C CD36 69B1 # Subkey fingerprint: F133 3857 4B66 2389 866C 7682 BFFB D25F 78C7 AE83 * remotes/bonzini/tags/for-upstream: hostmem: detect host backend memory is being used properly hostmem: fix QEMU crash by 'info memdev' char: do not use atexit cleanup handler net: do not use atexit for cleanup slirp: use exit notifier for slirp_smb_cleanup tap: use an exit notifier to call down_script util: Fix MIN_NON_ZERO qemu-sockets: use qapi_free_SocketAddress in cleanup disas: avoid including everything in headers compiled from C++ json-streamer: fix double-free on exiting during a parse main-loop: check return value before using pointer Use "-s" instead of "--quiet" to resolve non-fatal build error on FreeBSD. scsi-bus: Use longer sense buffer with scanners scsi-bus: Add SCSI scanner support Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2016-07-13Improve block job rate limiting for small bandwidth valuesSascha Silbe1-9/+34
ratelimit_calculate_delay() previously reset the accounting every time slice, no matter how much data had been processed before. This had (at least) two consequences: 1. The minimum speed is rather large, e.g. 5 MiB/s for commit and stream. Not sure if there are real-world use cases where this would be a problem. Mirroring and backup over a slow link (e.g. DSL) would come to mind, though. 2. Tests for block job operations (e.g. cancel) were rather racy All block jobs currently use a time slice of 100ms. That's a reasonable value to get smooth output during regular operation. However this also meant that the state of block jobs changed every 100ms, no matter how low the configured limit was. On busy hosts, qemu often transferred additional chunks until the test case had a chance to cancel the job. Fix the block job rate limit code to delay for more than one time slice to address the above issues. To make it easier to handle oversized chunks we switch the semantics from returning a delay _before_ the current request to a delay _after_ the current request. If necessary, this delay consists of multiple time slice units. Since the mirror job sends multiple chunks in one go even if the rate limit was exceeded in between, we need to keep track of the start of the current time slice so we can correctly re-compute the delay for the updated amount of data. The minimum bandwidth now is 1 data unit per time slice. The block jobs are currently passing the amount of data transferred in sectors and using 100ms time slices, so this translates to 5120 bytes/second. With chunk sizes usually being O(512KiB), tests have plenty of time (O(100s)) to operate on block jobs. The chance of a race condition now is fairly remote, except possibly on insanely loaded systems. Signed-off-by: Sascha Silbe <silbe@linux.vnet.ibm.com> Message-id: 1467127721-9564-2-git-send-email-silbe@linux.vnet.ibm.com Reviewed-by: Max Reitz <mreitz@redhat.com> Signed-off-by: Max Reitz <mreitz@redhat.com>
2016-07-13block/qdev: Allow configuring rerror/werror with qdev propertiesKevin Wolf2-0/+12
The rerror/werror policies are implemented in the devices, so that's where they should be configured. In comparison to the old options in -drive, the qdev properties are only added to those devices that actually support them. If the option isn't given (or "auto" is specified), the setting of the BlockBackend is used for compatibility with the old options. For block jobs, "auto" is the same as "enospc". Signed-off-by: Kevin Wolf <kwolf@redhat.com> Reviewed-by: Max Reitz <mreitz@redhat.com>
2016-07-13block/qdev: Allow configuring WCE with qdev propertiesKevin Wolf1-1/+4
As cache.writeback is a BlockBackend property and as such more related to the guest device than the BlockDriverState, we already removed it from the blockdev-add interface. This patch adds the new way to set it, as a qdev property of the corresponding guest device. For example: -drive if=none,file=test.img,node-name=img -device ide-hd,drive=img,write-cache=off Signed-off-by: Kevin Wolf <kwolf@redhat.com> Reviewed-by: Max Reitz <mreitz@redhat.com>
2016-07-13hostmem: detect host backend memory is being used properlyXiao Guangrong1-1/+3
Currently, we use memory_region_is_mapped() to detect if the host backend memory is being used. This works if the memory is directly mapped into guest's address space, however, it is not true for nvdimm as it uses aliased memory region to map the memory. This is why this bug can happen: https://bugzilla.redhat.com/show_bug.cgi?id=1352769 Fix it by introduce a new filed, is_mapped, to HostMemoryBackend, we set/clear this filed accordingly when the device link/unlink to host backend memory Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2016-07-13char: do not use atexit cleanup handlerMarc-André Lureau1-0/+7
It turns out qemu is calling exit() in various places from various threads without taking much care of resources state. The atexit() cleanup handlers cannot easily destroy resources that are in use (by the same thread or other). Since c1111a24a3, TCG arm guests run into the following abort() when running tests, the chardev mutex is locked during the write, so qemu_mutex_destroy() returns an error: #0 0x00007fffdbb806f5 in raise () at /lib64/libc.so.6 #1 0x00007fffdbb822fa in abort () at /lib64/libc.so.6 #2 0x00005555557616fe in error_exit (err=<optimized out>, msg=msg@entry=0x555555c38c30 <__func__.14622> "qemu_mutex_destroy") at /home/drjones/code/qemu/util/qemu-thread-posix.c:39 #3 0x0000555555b0be20 in qemu_mutex_destroy (mutex=mutex@entry=0x5555566aa0e0) at /home/drjones/code/qemu/util/qemu-thread-posix.c:57 #4 0x00005555558aab00 in qemu_chr_free_common (chr=0x5555566aa0e0) at /home/drjones/code/qemu/qemu-char.c:4029 #5 0x00005555558b05f9 in qemu_chr_delete (chr=<optimized out>) at /home/drjones/code/qemu/qemu-char.c:4038 #6 0x00005555558b05f9 in qemu_chr_delete (chr=<optimized out>) at /home/drjones/code/qemu/qemu-char.c:4044 #7 0x00005555558b062c in qemu_chr_cleanup () at /home/drjones/code/qemu/qemu-char.c:4557 #8 0x00007fffdbb851e8 in __run_exit_handlers () at /lib64/libc.so.6 #9 0x00007fffdbb85235 in () at /lib64/libc.so.6 #10 0x00005555558d1b39 in testdev_write (testdev=0x5555566aa0a0) at /home/drjones/code/qemu/backends/testdev.c:71 #11 0x00005555558d1b39 in testdev_write (chr=<optimized out>, buf=0x7fffc343fd9a "", len=0) at /home/drjones/code/qemu/backends/testdev.c:95 #12 0x00005555558adced in qemu_chr_fe_write (s=0x5555566aa0e0, buf=buf@entry=0x7fffc343fd98 "0q", len=len@entry=2) at /home/drjones/code/qemu/qemu-char.c:282 Instead of using a atexit() handler, only run the chardev cleanup as initially proposed at the end of main(), where there are less chances (hic) of conflicts or other races. Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com> Reported-by: Andrew Jones <drjones@redhat.com> Message-Id: <20160704153823.16879-1-marcandre.lureau@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2016-07-13coroutine: move entry argument to qemu_coroutine_createPaolo Bonzini2-7/+5
In practice the entry argument is always known at creation time, and it is confusing that sometimes qemu_coroutine_enter is used with a non-NULL argument to re-enter a coroutine (this happens in block/sheepdog.c and tests/test-coroutine.c). So pass the opaque value at creation time, for consistency with e.g. aio_bh_new. Mostly done with the following semantic patch: @ entry1 @ expression entry, arg, co; @@ - co = qemu_coroutine_create(entry); + co = qemu_coroutine_create(entry, arg); ... - qemu_coroutine_enter(co, arg); + qemu_coroutine_enter(co); @ entry2 @ expression entry, arg; identifier co; @@ - Coroutine *co = qemu_coroutine_create(entry); + Coroutine *co = qemu_coroutine_create(entry, arg); ... - qemu_coroutine_enter(co, arg); + qemu_coroutine_enter(co); @ entry3 @ expression entry, arg; @@ - qemu_coroutine_enter(qemu_coroutine_create(entry), arg); + qemu_coroutine_enter(qemu_coroutine_create(entry, arg)); @ reentry @ expression co; @@ - qemu_coroutine_enter(co, NULL); + qemu_coroutine_enter(co); except for the aforementioned few places where the semantic patch stumbled (as expected) and for test_co_queue, which would otherwise produce an uninitialized variable warning. Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Reviewed-by: Fam Zheng <famz@redhat.com> Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2016-07-13coroutine: use QSIMPLEQ instead of QTAILQPaolo Bonzini2-3/+3
CoQueue do not need to remove any element but the head of the list; processing is always strictly FIFO. Therefore, the simpler singly-linked QSIMPLEQ can be used instead. Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Reviewed-by: Fam Zheng <famz@redhat.com> Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2016-07-13osdep: Introduce qemu_dupFam Zheng1-0/+3
And use it in qemu_dup_flags. Signed-off-by: Fam Zheng <famz@redhat.com> Reviewed-by: Eric Blake <eblake@redhat.com> Reviewed-by: John Snow <jsnow@redhat.com> Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2016-07-13commit: Add 'job-id' parameter to 'block-commit'Alberto Garcia1-6/+10
This patch adds a new optional 'job-id' parameter to 'block-commit', allowing the user to specify the ID of the block job to be created. Signed-off-by: Alberto Garcia <berto@igalia.com> Reviewed-by: Kevin Wolf <kwolf@redhat.com> Reviewed-by: Max Reitz <mreitz@redhat.com> Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2016-07-13stream: Add 'job-id' parameter to 'block-stream'Alberto Garcia1-4/+6
This patch adds a new optional 'job-id' parameter to 'block-stream', allowing the user to specify the ID of the block job to be created. The HMP 'block_stream' command remains unchanged. Signed-off-by: Alberto Garcia <berto@igalia.com> Reviewed-by: Kevin Wolf <kwolf@redhat.com> Reviewed-by: Max Reitz <mreitz@redhat.com> Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2016-07-13backup: Add 'job-id' parameter to 'blockdev-backup' and 'drive-backup'Alberto Garcia1-3/+5
This patch adds a new optional 'job-id' parameter to 'blockdev-backup' and 'drive-backup', allowing the user to specify the ID of the block job to be created. The HMP 'drive_backup' command remains unchanged. Signed-off-by: Alberto Garcia <berto@igalia.com> Reviewed-by: Kevin Wolf <kwolf@redhat.com> Reviewed-by: Max Reitz <mreitz@redhat.com> Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2016-07-13mirror: Add 'job-id' parameter to 'blockdev-mirror' and 'drive-mirror'Alberto Garcia1-2/+4
This patch adds a new optional 'job-id' parameter to 'blockdev-mirror' and 'drive-mirror', allowing the user to specify the ID of the block job to be created. The HMP 'drive_mirror' command remains unchanged. Signed-off-by: Alberto Garcia <berto@igalia.com> Reviewed-by: Kevin Wolf <kwolf@redhat.com> Reviewed-by: Max Reitz <mreitz@redhat.com> Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2016-07-13blockjob: Add 'job_id' parameter to block_job_create()Alberto Garcia1-3/+5
When a new job is created, the job ID is taken from the device name of the BDS. This patch adds a new 'job_id' parameter to let the caller provide one instead. This patch also verifies that the ID is always unique and well-formed. This causes problems in a couple of places where no ID is being set, because the BDS does not have a device name. In the case of test_block_job_start() (from test-blockjob-txn.c) we can simply use this new 'job_id' parameter to set the missing ID. In the case of img_commit() (from qemu-img.c) we still don't have the API to make commit_active_start() set the job ID, so we solve it by setting a default value. We'll get rid of this as soon as we extend the API. Signed-off-by: Alberto Garcia <berto@igalia.com> Reviewed-by: Max Reitz <mreitz@redhat.com> Reviewed-by: Kevin Wolf <kwolf@redhat.com> Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2016-07-13blockjob: Add block_job_get()Alberto Garcia1-0/+10
Currently the way to look for a specific block job is to iterate the list manually using block_job_next(). Since we want to be able to identify a job primarily by its ID it makes sense to have a function that does just that. Signed-off-by: Alberto Garcia <berto@igalia.com> Reviewed-by: Max Reitz <mreitz@redhat.com> Reviewed-by: Kevin Wolf <kwolf@redhat.com> Signed-off-by: Kevin Wolf <kwolf@redhat.com>
generated by cgit v1.2.1 (git 2.18.0) at 2024-07-08 13:40:45 +0000