summaryrefslogtreecommitdiff
path: root/hw/ssi
AgeCommit message (Collapse)AuthorFilesLines
2018-04-26xilinx_spips: Correct SNOOP_NONE state when flushing the txfifoSai Pavan Boddu1-1/+2
SNOOP_NONE state handle is moved above in the if ladder, as it's same as SNOOP_STRIPPING during data cycles. Signed-off-by: Sai Pavan Boddu <saipava@xilinx.com> Reviewed-by: Francisco Iglesias <frasse.iglesias@gmail.com> Message-id: 1524119244-1240-1-git-send-email-saipava@xilinx.com Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2018-03-01xilinx_spips: Use 8 dummy cycles with the QIOR/QIOR4 commandsFrancisco Iglesias1-1/+1
Use 8 dummy cycles (4 dummy bytes) with the QIOR/QIOR4 commands in legacy mode for matching what is expected by Micron (Numonyx) flashes (the default target flash type of the QSPI). Signed-off-by: Francisco Iglesias <frasse.iglesias@gmail.com> Tested-by: Alistair Francis <alistair.francis@xilinx.com> Reviewed-by: Alistair Francis <alistair.francis@xilinx.com> Message-id: 20180223232233.31482-3-frasse.iglesias@gmail.com Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2018-03-01xilinx_spips: Enable only two slaves when reading/writing with stripeFrancisco Iglesias1-4/+37
Assert only the lower cs on bus 0 and upper cs on bus 1 when both buses and chip selects are enabled (e.g reading/writing with stripe). Signed-off-by: Francisco Iglesias <frasse.iglesias@gmail.com> Reviewed-by: Alistair Francis <alistair.francis@xilinx.com> Tested-by: Alistair Francis <alistair.francis@xilinx.com> Message-id: 20180223232233.31482-2-frasse.iglesias@gmail.com Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2018-02-09Include qapi/error.h exactly where neededMarkus Armbruster1-1/+0
This cleanup makes the number of objects depending on qapi/error.h drop from 1910 (out of 4743) to 1612 in my "build everything" tree. While there, separate #include from file comment with a blank line, and drop a useless comment on why qemu/osdep.h is included first. Reviewed-by: Eric Blake <eblake@redhat.com> Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Signed-off-by: Markus Armbruster <armbru@redhat.com> Message-Id: <20180201111846.21846-5-armbru@redhat.com> [Semantic conflict with commit 34e304e975 resolved, OSX breakage fixed]
2018-01-25xilinx_spips: Correct usage of an uninitialized local variableFrancisco Iglesias1-1/+17
Coverity found that the variable tx_rx in the function xilinx_spips_flush_txfifo was being used uninitialized (CID 1383841). This patch corrects this by always initializing tx_rx to zeros. Signed-off-by: Francisco Iglesias <frasse.iglesias@gmail.com> Message-id: 20180124215708.30400-1-frasse.iglesias@gmail.com Reviewed-by: Peter Maydell <peter.maydell@linaro.org> Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2018-01-22Replace all occurances of __FUNCTION__ with __func__Alistair Francis1-3/+3
Replace all occurs of __FUNCTION__ except for the check in checkpatch with the non GCC specific __func__. One line in hcd-musb.c was manually tweaked to pass checkpatch. Signed-off-by: Alistair Francis <alistair.francis@xilinx.com> Reviewed-by: Eric Blake <eblake@redhat.com> Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com> Reviewed-by: Anthony PERARD <anthony.perard@citrix.com> Reviewed-by: Juan Quintela <quintela@redhat.com> Reviewed-by: Gerd Hoffmann <kraxel@redhat.com> [THH: Removed hunks related to pxa2xx_mmci.c (fixed already)] Signed-off-by: Thomas Huth <thuth@redhat.com>
2018-01-16maint: Fix macros with broken 'do/while(0); ' usageEric Blake4-4/+4
The point of writing a macro embedded in a 'do { ... } while (0)' loop (particularly if the macro has multiple statements or would otherwise end with an 'if' statement) is so that the macro can be used as a drop-in statement with the caller supplying the trailing ';'. Although our coding style frowns on brace-less 'if': if (cond) statement; else something else; that is the classic case where failure to use do/while(0) wrapping would cause the 'else' to pair with any embedded 'if' in the macro rather than the intended outer 'if'. But conversely, if the macro includes an embedded ';', then the same brace-less coding style would now have two statements, making the 'else' a syntax error rather than pairing with the outer 'if'. Thus, even though our coding style with required braces is not impacted, ending a macro with ';' makes our code harder to port to projects that use brace-less styles. The change should have no semantic impact. I was not able to fully compile-test all of the changes (as some of them are examples of the ugly bit-rotting debug print statements that are completely elided by default, and I didn't want to recompile with the necessary -D witnesses - cleaning those up is left as a bite-sized task for another day); I did, however, audit that for all files touched, all callers of the changed macros DID supply a trailing ';' at the callsite, and did not appear to be used as part of a brace-less conditional. Found mechanically via: $ git grep -B1 'while (0);' | grep -A1 \\\\ Signed-off-by: Eric Blake <eblake@redhat.com> Acked-by: Cornelia Huck <cohuck@redhat.com> Reviewed-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Dr. David Alan Gilbert <dgilbert@redhat.com> Message-Id: <20171201232433.25193-7-eblake@redhat.com> Reviewed-by: Juan Quintela <quintela@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2017-12-18hw/ssi/aspeed_smc: remove unused #includePhilippe Mathieu-Daudé1-1/+0
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Reviewed-by: Peter Maydell <peter.maydell@linaro.org> Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
2017-12-18misc: avoid "include/" in include pathPhilippe Mathieu-Daudé1-1/+1
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Reviewed-by: Peter Maydell <peter.maydell@linaro.org> Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
2017-12-13xilinx_spips: Use memset instead of a for loop to zero registersAlistair Francis1-8/+3
Use memset() instead of a for loop to zero all of the registers. Signed-off-by: Alistair Francis <alistair.francis@xilinx.com> Reviewed-by: KONRAD Frederic <frederic.konrad@adacore.com> Reviewed-by: Francisco Iglesias <frasse.iglesias@gmail.com> Message-id: c076e907f355923864cb1afde31b938ffb677778.1513104804.git.alistair.francis@xilinx.com Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2017-12-13xilinx_spips: Set all of the reset valuesAlistair Francis1-5/+30
Following the ZynqMP register spec let's ensure that all reset values are set. Signed-off-by: Alistair Francis <alistair.francis@xilinx.com> Reviewed-by: Francisco Iglesias <frasse.iglesias@gmail.com> Message-id: 19836f3e0a298b13343c5a59c87425355e7fd8bd.1513104804.git.alistair.francis@xilinx.com Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2017-12-13xilinx_spips: Update the QSPI Mod ID reset valueAlistair Francis1-0/+1
Update the reset value to match the latest ZynqMP register spec. Signed-off-by: Alistair Francis <alistair.francis@xilinx.com> Reviewed-by: KONRAD Frederic <frederic.konrad@adacore.com> Reviewed-by: Francisco Iglesias <frasse.iglesias@gmail.com> Message-id: c03e51d041db7f055596084891aeb1e856e32b9f.1513104804.git.alistair.francis@xilinx.com Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2017-12-13xilinx_spips: Add support for the ZynqMP Generic QSPIFrancisco Iglesias1-47/+532
Add support for the Zynq Ultrascale MPSoc Generic QSPI. Signed-off-by: Francisco Iglesias <frasse.iglesias@gmail.com> Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com> Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com> Message-id: 20171126231634.9531-13-frasse.iglesias@gmail.com Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2017-12-13xilinx_spips: Don't set TX FIFO UNDERFLOW at cmd doneFrancisco Iglesias1-3/+1
Don't set TX FIFO UNDERFLOW interrupt after transmitting the commands. Also update interrupts after reading out the interrupt status. Signed-off-by: Francisco Iglesias <frasse.iglesias@gmail.com> Acked-by: Alistair Francis <alistair.francis@xilinx.com> Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com> Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com> Message-id: 20171126231634.9531-12-frasse.iglesias@gmail.com Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2017-12-13xilinx_spips: Add support for 4 byte addresses in the LQSPIFrancisco Iglesias1-1/+5
Add support for 4 byte addresses in the LQSPI and correct LQSPI_CFG_SEP_BUS. Signed-off-by: Francisco Iglesias <frasse.iglesias@gmail.com> Reviewed-by: Alistair Francis <alistair.francis@xilinx.com> Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com> Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com> Message-id: 20171126231634.9531-11-frasse.iglesias@gmail.com Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2017-12-13xilinx_spips: Add support for zero pumpingFrancisco Iglesias1-7/+40
Add support for zero pumping according to the transfer size register. Signed-off-by: Francisco Iglesias <frasse.iglesias@gmail.com> Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com> Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com> Message-id: 20171126231634.9531-10-frasse.iglesias@gmail.com Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2017-12-13xilinx_spips: Make tx/rx_data_bytes more generic and reusableFrancisco Iglesias1-27/+37
Make tx/rx_data_bytes more generic so they can be reused (when adding support for the Zynqmp Generic QSPI). Signed-off-by: Francisco Iglesias <frasse.iglesias@gmail.com> Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com> Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com> Message-id: 20171126231634.9531-9-frasse.iglesias@gmail.com Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2017-12-13xilinx_spips: Add support for RX discard and RX drainFrancisco Iglesias1-18/+149
Add support for the RX discard and RX drain functionality. Also transmit one byte per dummy cycle (to the flash memories) with commands that require these. Signed-off-by: Francisco Iglesias <frasse.iglesias@gmail.com> Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com> Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com> Message-id: 20171126231634.9531-8-frasse.iglesias@gmail.com Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2017-12-13xilinx_spips: Update striping to be big-endian bit orderFrancisco Iglesias1-9/+10
Update striping functionality to be big-endian bit order (as according to the Zynq-7000 Technical Reference Manual). Output thereafter the even bits into the flash memory connected to the lower QSPI bus and the odd bits into the flash memory connected to the upper QSPI bus. Signed-off-by: Francisco Iglesias <frasse.iglesias@gmail.com> Acked-by: Alistair Francis <alistair.francis@xilinx.com> Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com> Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com> Message-id: 20171126231634.9531-7-frasse.iglesias@gmail.com Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2017-12-13xilinx_spips: Move FlashCMD, XilinxQSPIPS and XilinxSPIPSClassFrancisco Iglesias1-35/+0
Move the FlashCMD enum, XilinxQSPIPS and XilinxSPIPSClass structures to the header for consistency (struct XilinxSPIPS is found there). Also move out a define and remove two double included headers (while touching the code). Finally, add 4 byte address commands to the FlashCMD enum. Signed-off-by: Francisco Iglesias <frasse.iglesias@gmail.com> Reviewed-by: Alistair Francis <alistair.francis@xilinx.com> Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com> Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com> Message-id: 20171126231634.9531-6-frasse.iglesias@gmail.com Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2017-10-31msf2: Remove dead code reported by CoveritySubbaraya Sundeep1-4/+14
Fixed incorrect frame size mask, validated maximum frame size in spi_write and removed dead code. Signed-off-by: Subbaraya Sundeep <sundeep.lkml@gmail.com> Reviewed-by: Darren Kenny <darren.kenny@oracle.com> Reviewed-by: Alistair Francis <alistair.francis@xilinx.com> Message-id: 1508898544-10307-1-git-send-email-sundeep.lkml@gmail.com Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2017-09-21msf2: Add Smartfusion2 SPI controllerSubbaraya Sundeep2-0/+405
Modelled Microsemi's Smartfusion2 SPI controller. Signed-off-by: Subbaraya Sundeep <sundeep.lkml@gmail.com> Reviewed-by: Alistair Francis <alistair.francis@xilinx.com> Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Message-id: 20170920201737.25723-4-f4bug@amsat.org Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2017-08-14xlnx-qspi: add a property for mmio-executionKONRAD Frederic1-3/+33
This adds mmio-exec property to workaround the migration bug. When enabled the migration is blocked and will return an error. Signed-off-by: KONRAD Frederic <frederic.konrad@adacore.com> Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com> Message-id: 1502438052-5117-1-git-send-email-frederic.konrad@adacore.com Reviewed-by: Peter Maydell <peter.maydell@linaro.org> Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2017-06-27xilinx_spips: allow mmio executionKONRAD Frederic1-19/+55
This allows to execute from the lqspi area. When the request_ptr is called the device loads 1024bytes from the SPI device. Then this code can be executed by the guest. Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com> Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com> Signed-off-by: KONRAD Frederic <fred.konrad@greensocs.com> Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
2017-02-10aspeed/smc: use a modulo to check segment limitsCédric Le Goater1-2/+2
The size of a segment is not necessarily a power of 2. Signed-off-by: Cédric Le Goater <clg@kaod.org> Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Message-id: 1486648058-520-5-git-send-email-clg@kaod.org Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2017-02-10aspeed/smc: handle dummies only in fast read modeCédric Le Goater1-3/+6
HW works fine in normal read mode with dummy bytes being set. So let's check this case to not transfer bytes. Signed-off-by: Cédric Le Goater <clg@kaod.org> Message-id: 1486648058-520-4-git-send-email-clg@kaod.org Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2017-01-27aspeed/smc: handle dummy bytes when doing fast reads in command modeCédric Le Goater1-0/+21
When doing fast read, a certain amount of dummy bytes should be sent before the read. This number is configurable in the controler CE0 Control Register and needs to be modeled using fake transfers to the flash module. This only supports command mode. User mode requires more work and a possible extension of the m25p80 device model. Signed-off-by: Cédric Le Goater <clg@kaod.org> Acked-by: Marcin Krzemiński <mar.krzeminski@gmail.com> Message-id: 1484751701-2646-1-git-send-email-clg@kaod.org Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2017-01-20aspeed/smc: handle SPI flash Command modeCédric Le Goater1-25/+130
The Aspeed SMC controllers have a mode (Command mode) in which accesses to the flash content are no different than doing MMIOs. The controller generates all the necessary commands to load (or store) data in memory. However, accesses are restricted to the segment window assigned the the flash module by the controller. This window is defined by the Segment Address Register. Signed-off-by: Cédric Le Goater <clg@kaod.org> Reviewed-by: Andrew Jeffery <andrew@aj.id.au> Message-id: 1483979087-32663-8-git-send-email-clg@kaod.org [PMM: Deleted now-unused aspeed_smc_is_usermode() function] Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2017-01-20aspeed/smc: adjust the size of the register regionCédric Le Goater1-15/+10
The SPI controller of the AST2400 SoC has less registers. So we can adjust the size of the memory region holding the registers depending on the controller type. We can also remove the guest_error logging which is useless as the range of the region is strict enough. Signed-off-by: Cédric Le Goater <clg@kaod.org> Reviewed-by: Joel Stanley <joel@jms.id.au> Message-id: 1483979087-32663-7-git-send-email-clg@kaod.org Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2017-01-20aspeed/smc: unfold the AspeedSMCController arrayCédric Le Goater1-18/+73
This is getting difficult to read. Also add a 'has_dma' field for each controller type. Signed-off-by: Cédric Le Goater <clg@kaod.org> Reviewed-by: Joel Stanley <joel@jms.id.au> Reviewed-by: Andrew Jeffery <andrew@aj.id.au> Message-id: 1483979087-32663-6-git-send-email-clg@kaod.org Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2017-01-20aspeed/smc: autostrap CE0/1 configurationCédric Le Goater1-5/+27
On the AST2500 SoC, the FMC controller flash type is fixed to SPI for CE0 and CE1 and 4BYTE mode is autodetected for CE0. On the AST2400 SoC, the FMC controller flash type and 4BYTE mode are strapped with register SCU70. We use the default settings from the palmetto-bmc machine for now. Signed-off-by: Cédric Le Goater <clg@kaod.org> Reviewed-by: Joel Stanley <joel@jms.id.au> Reviewed-by: Andrew Jeffery <andrew@aj.id.au> Message-id: 1483979087-32663-5-git-send-email-clg@kaod.org Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2017-01-20aspeed/smc: rework the prototype of the AspeedSMCFlash helper routinesCédric Le Goater1-17/+22
Change the routines prototype to use a 'AspeedSMCFlash *' instead of 'AspeedSMCState *'. The result will help in making future changes clearer. Also change aspeed_smc_update_cs() which uselessly loops on all slave devices to update their status. Signed-off-by: Cédric Le Goater <clg@kaod.org> Reviewed-by: Joel Stanley <joel@jms.id.au> Reviewed-by: Andrew Jeffery <andrew@aj.id.au> Message-id: 1483979087-32663-4-git-send-email-clg@kaod.org Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2017-01-20aspeed/smc: remove call to aspeed_smc_update_cs() in reset functionCédric Le Goater1-2/+1
Instead, we can simply set the irq level when unselecting the slave devices. This change prepares ground for a subsequent cleanup of the aspeed_smc_update_cs() routine which uselessly loops on all slaves to update their status. Signed-off-by: Cédric Le Goater <clg@kaod.org> Message-id: 1483979087-32663-3-git-send-email-clg@kaod.org Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2017-01-20aspeed/smc: remove call to reset in realize functionCédric Le Goater1-2/+0
This is useless as reset will be called later on. Signed-off-by: Cédric Le Goater <clg@kaod.org> Acked-by: Marcin Krzemiński <mar.krzeminski@gmail.com> Message-id: 1483979087-32663-2-git-send-email-clg@kaod.org Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2017-01-09hw/ssi/imx_spi.c: Remove MSGDATA register supportJean-Christophe Dubois1-3/+8
From the documentation it is not clear what this SPI register is about. Moreover, neither linux driver nor xvisor driver are using this SPI register. For now we just remove it and issue a log on register write access. Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net> Message-id: 20170107122047.26300-1-jcd@tribudubois.net Reviewed-by: Peter Maydell <peter.maydell@linaro.org> Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2016-12-27aspeed/smc: improve segment register supportCédric Le Goater1-8/+9
The HW does not enforce all the rules in the specs and allows a few "curious" setups like zero size segments and overlaps. So change the model to be in sync but keep the warnings which are always interesting for debug. Signed-off-by: Cédric Le Goater <clg@kaod.org> Reviewed-by: Joel Stanley <joel@jms.id.au> Message-id: 1480434248-27138-13-git-send-email-clg@kaod.org Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2016-10-24xilinx: fix buffer overflow on realizePaolo Bonzini1-2/+5
ASAN complains about buffer overflow when running: aarch64-softmmu/qemu-system-aarch64 -machine xilinx-zynq-a9 ==476==ERROR: AddressSanitizer: heap-buffer-overflow on address 0x602000035e38 at pc 0x000000f75253 bp 0x7ffc597e0ec0 sp 0x7ffc597e0eb0 READ of size 8 at 0x602000035e38 thread T0 #0 0xf75252 in xilinx_spips_realize hw/ssi/xilinx_spips.c:623 #1 0xb9ef6c in device_set_realized hw/core/qdev.c:918 #2 0x129ae01 in property_set_bool qom/object.c:1854 #3 0x1296e70 in object_property_set qom/object.c:1088 #4 0x129dd1b in object_property_set_qobject qom/qom-qobject.c:27 #5 0x1297168 in object_property_set_bool qom/object.c:1157 #6 0xb9aeac in qdev_init_nofail hw/core/qdev.c:358 #7 0x78a5bf in zynq_init_spi_flashes /home/elmarco/src/qemu/hw/arm/xilinx_zynq.c:125 #8 0x78af60 in zynq_init /home/elmarco/src/qemu/hw/arm/xilinx_zynq.c:238 #9 0x998eac in main /home/elmarco/src/qemu/vl.c:4534 #10 0x7f96ed692730 in __libc_start_main (/lib64/libc.so.6+0x20730) #11 0x41d0a8 in _start (/home/elmarco/src/qemu/aarch64-softmmu/qemu-system-aarch64+0x41d0a8) 0x602000035e38 is located 0 bytes to the right of 8-byte region [0x602000035e30,0x602000035e38) allocated by thread T0 here: #0 0x7f970b014e60 in malloc (/lib64/libasan.so.3+0xc6e60) #1 0x7f96f15b0e18 in g_malloc (/lib64/libglib-2.0.so.0+0x4ee18) #2 0xb9ef6c in device_set_realized hw/core/qdev.c:918 #3 0x129ae01 in property_set_bool qom/object.c:1854 #4 0x1296e70 in object_property_set qom/object.c:1088 #5 0x129dd1b in object_property_set_qobject qom/qom-qobject.c:27 #6 0x1297168 in object_property_set_bool qom/object.c:1157 #7 0xb9aeac in qdev_init_nofail hw/core/qdev.c:358 #8 0x78a5bf in zynq_init_spi_flashes /home/elmarco/src/qemu/hw/arm/xilinx_zynq.c:125 #9 0x78af60 in zynq_init /home/elmarco/src/qemu/hw/arm/xilinx_zynq.c:238 #10 0x998eac in main /home/elmarco/src/qemu/vl.c:4534 #11 0x7f96ed692730 in __libc_start_main (/lib64/libc.so.6+0x20730) s->spi is allocated with the size of num_busses which may be 1 (by default). Change to use a loop up to s->num_busses also for the call to ssi_auto_connect_slaves(). Reported-by: Marc-André Lureau <marcandre.lureau@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2016-10-17aspeed: add support for the SMC segment registersCédric Le Goater1-5/+130
The SMC controller on the Aspeed SoC has a set of registers to configure the mapping of each flash module in the SoC address space. Writing to these registers triggers a remap of the memory region and the spec requires a certain number of checks before doing so. Signed-off-by: Cédric Le Goater <clg@kaod.org> Reviewed-by: Andrew Jeffery <andrew@aj.id.au> Message-id: 1474977462-28032-7-git-send-email-clg@kaod.org Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2016-10-17aspeed: create mapping regions for the maximum number of slavesCédric Le Goater1-3/+13
The SMC controller on the Aspeed SoC has a set of registers to configure the mapping of each flash module in the SoC address space. These mapping windows are configurable even though no SPI slave is attached to the controller. Also rewrite a bit the comments in the code on this topic. Signed-off-by: Cédric Le Goater <clg@kaod.org> Reviewed-by: Andrew Jeffery <andrew@aj.id.au> Message-id: 1474977462-28032-6-git-send-email-clg@kaod.org Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2016-10-17aspeed: add support for the AST2500 SoC SMC controllersCédric Le Goater1-1/+27
The SMC controllers on the Aspeed AST2500 SoC are very similar to the ones found on the AST2400. The differences are on the number of supported flash modules and their default mappings in the SoC address space. The Aspeed AST2500 has one SPI controller for the BMC firmware and two for the host firmware. All controllers have now the same set of registers compatible with the AST2400 FMC controller and the legacy 'SMC' controller is fully gone. We keep the FMC object to act as the BMC SPI controller and add a new SPI controller for the host. We also have to introduce new type names to handle the differences in the flash modules memory mappping. Signed-off-by: Cédric Le Goater <clg@kaod.org> Reviewed-by: Andrew Jeffery <andrew@aj.id.au> Message-id: 1474977462-28032-5-git-send-email-clg@kaod.org Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2016-10-17aspeed: move the flash module mapping address under the controller definitionCédric Le Goater1-4/+11
This will ease the definition of the new controllers for the AST2500 SoC and also ease the support of the segment registers, which provide a way to reconfigure the mapping window of each slave. Signed-off-by: Cédric Le Goater <clg@kaod.org> Reviewed-by: Andrew Jeffery <andrew@aj.id.au> Message-id: 1474977462-28032-3-git-send-email-clg@kaod.org Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2016-10-04STM32F2xx: Add the SPI deviceAlistair Francis2-0/+226
Add the STM32F2xx SPI device. Signed-off-by: Alistair Francis <alistair@alistair23.me> Reviewed-by: Peter Maydell <peter.maydell@linaro.org> Message-id: 8197811d5c94f814fa67c6a33ca2f7fd0aa97432.1474742262.git.alistair@alistair23.me Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2016-09-22imx: Use 'const char', not 'char const'Peter Maydell1-1/+1
'char const' means the same thing as 'const char', but we use the former in only a handful of places and we use the latter over six thousand times. Switch the imx reg_name() functions to bring them in line with everything else. Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2016-07-14ast2400: pretend DMAs are done for U-bootCédric Le Goater1-0/+4
U-boot does SPI timing calibration using DMA tranfers. To let the initialization continue, we fake success by setting the DMA status of the Interrupt Control Register. For the moment, DMA support is not required as it is not used in normal operation. Signed-off-by: Cédric Le Goater <clg@kaod.org> Message-id: 1467994016-11678-4-git-send-email-clg@kaod.org Reviewed-by: Peter Maydell <peter.maydell@linaro.org> Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2016-07-14ast2400: replace aspeed_smc_is_implemented()Cédric Le Goater1-20/+15
aspeed_smc_is_implemented() filters invalid registers in a peculiar way. Let's remove it and open code the if conditions. It serves the same purpose, the aesthetic is better, and new registers can easily be added. Signed-off-by: Cédric Le Goater <clg@kaod.org> Message-id: 1467994016-11678-3-git-send-email-clg@kaod.org Reviewed-by: Peter Maydell <peter.maydell@linaro.org> Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2016-07-04ast2400: add SPI flash slavesCédric Le Goater1-3/+147
Each controller on the ast2400 has a memory range on which it maps its flash module slaves. Each slave is assigned a memory segment for its mapping that can be changed at bootime with the Segment Address Register. This is not supported in the current implementation so we are using the defaults provided by the specs. Each SPI flash slave can then be accessed in two modes: Command and User. When in User mode, accesses to the memory segment of the slaves are translated in SPI transfers. When in Command mode, the HW generates the SPI commands automatically and the memory segment is accessed as if doing a MMIO. Other SPI controllers call that mode linear addressing mode. For this purpose, we are adding below each crontoller an array of structs gathering for each SPI flash module, a segment rank, a MemoryRegion to handle the memory accesses and the associated SPI slave device, which should be a m25p80. Only the User mode is supported for now but we are preparing ground for the Command mode. The framework is sufficient to support Linux. Signed-off-by: Cédric Le Goater <clg@kaod.org> Message-id: 1467138270-32481-8-git-send-email-clg@kaod.org [PMM: Use g_new0() rather than g_malloc0()] Reviewed-by: Peter Maydell <peter.maydell@linaro.org> Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2016-07-04ast2400: add SMC controllers (FMC and SPI)Cédric Le Goater2-0/+327
The Aspeed AST2400 soc includes a static memory controller for the BMC which supports NOR, NAND and SPI flash memory modules. This controller has two modes : the SMC for the legacy interface which supports only one module and the FMC for the new interface which supports up to five modules. The AST2400 also includes a SPI only controller used for the host firmware, commonly called BIOS on Intel. It can be used in three mode : a SPI master, SPI slave and SPI pass-through Below is the initial framework for the SMC controller (FMC mode only) and the SPI controller: the sysbus object, MMIO for registers configuration and controls. Each controller has a SPI bus and a configurable number of CS lines for SPI flash slaves. The differences between the controllers are small, so they are abstracted using indirections on the register numbers. Only SPI flash modules are supported. Signed-off-by: Cédric Le Goater <clg@kaod.org> Message-id: 1467138270-32481-7-git-send-email-clg@kaod.org Reviewed-by: Peter Maydell <peter.maydell@linaro.org> [PMM: added one missing error_propagate] Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2016-07-04ssi: change ssi_slave_init to be a realize opsCédric Le Goater1-3/+3
This enables qemu to handle late inits and report errors. All the SSI slave routine names were changed accordingly. Code was modified to handle errors when possible (m25p80 and ssi-sd) Tested with the m25p80 slave object. Suggested-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Cédric Le Goater <clg@kaod.org> Message-id: 1467138270-32481-2-git-send-email-clg@kaod.org Reviewed-by: Peter Maydell <peter.maydell@linaro.org> Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2016-05-19hw: explicitly include qemu/log.hPaolo Bonzini2-0/+2
Move the inclusion out of hw/hw.h, most files do not need it. Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2016-05-12i.MX: Add the Freescale SPI ControllerJean-Christophe DUBOIS2-0/+455
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net> Reviewed-by: Peter Maydell <peter.maydell@linaro.org> Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
generated by cgit v1.2.1 (git 2.18.0) at 2024-05-19 01:20:24 +0000